Bedienungsanleitung Ferm SGM1011 (Seite 7 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510106

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

and a slow speed will give a heavy coat. Apply

one coat at a time. If a further coat is required,

make sure you observe the manufacturers

drying time recommendations before applying a

second coat. When spraying small areas, keep

the output control on a low setting. This will avoid

using too much paint and prevent overspray.

Where possible, avoid stopping and starting when

spraying an object. This can lead to too much,

or not enough paint being applied. Do not tip the

spray gun to more than 45°.



Make sure that the machine is not live

when carrying out maintenance work on

the motor.

This machine has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Troubleshooting

 

 

• Worn swirl head.

• Replace swirl head.

• Pick up pipe not in the right position.

• Re-adjust pick up pipe.

• Blocked pick up pipe.

• Clean with thinner.

• Blocked nozzle.

• Clean nozzle.

• Blocked filter.

• Clean with thinner.

• Control knob needs adjustment.

• Adjust.

 

• Volume adjustment is not correct.

• Adjust.

• Paint too thick.

• Check viscosity of the paint.

 

• Too much paint.

• Adjust the volume clockwise to reduce

spraying. Two thin coats are better then

one thick coat.

• Viscosity too low.

• Check viscosity.

 

• Spray gun not clean, or not lubricated,

resulting in piston being stuck in cylinder.

• Disassemble spray gun and clean with

thinner.

 

• No electricity.

• Check power supply.

 

• Poor output adjustment.

• Re-adjust.

• Not enough paint in the container resulting in

air being sucked in.

• Refill with paint.

• Not diluting properly or not passing pick up

pipe completely.

• Check pick up pipe and viscosity level.

 

• Incorrect solvent is used.

• Use correct solvent.

• Spray gun too far from the surface.

• Hold spray gun closer to the object.

• Paint too thick.

• Thin the paint.

Cleaning and maintenance

Fig. G

Always remember to disconnect from the

mains supply before cleaning the spray

gun or paint container.

It is essential that the spray gun is cleaned

thoroughly after every use. Failure to clean will

almost certainly result in blockages and the spray

gun might not operate next time it is being used.

The warranty does not cover malfunction due to

failure to clean the spray gun properly.

The following actions must be taken after every

use and if the spray gun is not going to be used for

a longer period. Not taking the following actions

can cause the paint to dry;

• Switch off the machine.

• Press the trigger so the paint will flow back in

the container.

• Unscrew the container and pour the paint

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm SGM1011 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info