Bedienungsanleitung Ferm SGM1019 (Seite 8 von 24) (Englisch, Holländisch)

798919

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with a standardized test given in

EN60745; it may be used to compare one tool

with another and as a preliminary assessment of

exposure to vibration when using the tool for the

applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories,

may significantly increase the exposure level.

• The times when the tool is switched off or

when it is running but not actually doing the

job, may significantly reduce the exposure

level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2.

1. Machine

2. Battery

3. Battery unlock button

4. LED work light

5. Trigger

6. Cartridge shaft

7. Reload lever

8. LED work light switch

9. Safety tip

10. Belt hook

11. Adjustment knob

12. Battery LED indicators button

13. Battery LED indicators

14. Charger

15. Charger LED indicators

3. ASSEMBLY

The battery must be charged before first

use.

Removing the battery from the machine

Fig. B

• Push the battery unlock buttons (3) and pull

the battery out of the machine.

Inserting the battery into the machine

Fig. B

Ensure that the exterior of the battery is

clean and dry before connecting to the

charger or machine.

• Insert the battery (2) into the base of the

machine.

• Push the battery further forward until it clicks

into place.

Charging the battery (with the charger)

Fig. C

• Plug the charger plug into an electrical outlet

and wait for a while.

• Plug the output of the charger into the round

socket of the battery. The LED indicator on

the battery (15) will lighten up and show the

charging status.

LED indicator (15)

Fig. C

The battery has 1 LED indicator (15) which

indicates the status of the charging process:

LED Charger status

Red Battery charging in progress

Green Battery charging finished, battery fully charged

• After the battery is fully charged remove the

charger plug from the outlet and remove the

battery from the charger.

When the machine is not being used

over a longer period of time it is best to

store the battery in charged condition.

Application (Fig. D)

For this tool, use one of the following length for

staples or nails:

• Staples: Type 55: 15-25mm

• Nails: Type 47: 15, 20, 25, 30 or 32mm

Loading the nails or staples (Fig. D-G)

• Choose the correct nail or staple for the job.

• Place the tacker (1) on its side with the battery

(2) pointing to the right, like show in fig. E.

• Open de cartridge shaft (6) by slightly pressing

the reload lever (7).

• Pull the reload lever (7) to the right to open the

cartridge shaft (6).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm SGM1019 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info