Bedienungsanleitung Ferm SSM1007 (Seite 7 von 92) (Alle Sprachen)

697793

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

To stop the machine, release the Foot pedal

switch (10). Push the red OFF-switch (1) to turn

the machine off.

Tilting the table

Fig. A, D

The scroll saw table can be tilted from 0 to 45°.

To do so:

• Untighten the Angle adjustment knob (2) by

turning it anti-clockwise.

• Manually tilt the table until the desired angle

has been reached (see the graduated scale on

the machine).

• Retighten the Angle adjustment knob (2) by

turning it clockwise.

Removing the saw blade

Fig. E

Always disconnect the machine from the

main power supply before carrying out

any maintenance work.

• Untighten the Spanner (6) by turning it

clockwise until the spring is slack.

• Pull the Table inlay (9) upwards out of the saw

table to achieve a clear view of the blade, as

shown on fig. E1.

• Carefully push down the upper saw-blade

holder and slightly lift the blade in order to

facilitate its removal, as shown on fig. E2.

• Allow the blade to drop down slightly and push

it forward, in order to loosen it from the lower

holder.

Installing the saw blade

Fig. E

Always disconnect the machine from the

main power supply before carrying out

any maintenance work.

Use universal saw blades from any

better DIY shop or machine shop.

• Select the correct blade for the kind of wood to

be cut.

• Untighten the Spanner (6) by turning it

clockwise until the spring is slack.

• Pull the Table inlay (9) upwards out of the saw

table to achieve a clear view of the blade, as

shown on fig. E1.

• Push the saw blade through the slot, with the

teeth pointing downwards. Make sure that the

bolt of the saw blade (or saw-blade adapter)

slides into the lower saw blade holder.

• Pull the saw blade up, so that the upper bolt

(or saw-blade adapter) slides into the upper

holder.

• Push the Table inlay (9) downwards into the

saw table.

• Retighten the Spanner (6) by turning it anti-

clockwise until the saw blade has the required

tension.

• Remove all tools and other objects from the

saw table. Activate the current and allow the

saw blade to run before starting to saw.

The saw blade should run quietly.

Adjusting the saw blade position

Fig. F

The saw blade can be mounted in two different

positions: regular frontal position as shown on

Fig. F1 and in sideways position as shown on

Fig. F2. When using the sideways position, even

longer workpieces ca be sawed with ease.

Adapters for universal saw blades

Fig. G

The enclosed adapters should only be used with

universal (= without pins on the end) saw blades

• Unscrew the Allen screws on the adapter anti-

clockwise as shown on fig. G1

• Slide the universal saw into the gap between

the Allen screws

• Tighten the Allen screws clockwise so the saw

is clamped

• Install the saw blade (see INSTALLING THE

SAW BLADE) on the saw blade holders as

shown on fig. G2

Workpiece holder

Fig. A, H

The workpiece holder (8) is used to hold the

workpiece to the saw table, preventing the

workpiece from moving up and down due to the

movement of the blade. The workpiece holder

must be adjusted in height depending on the

thickness of the workpiece.

• Untighten the Locking knob (12) by turning it

anti-clockwise.

• Adjust the height of the Workpiece holder (8) to

the desired height.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm SSM1007 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info