Bedienungsanleitung Ferm TDM1022 (Seite 6 von 40) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

632654

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

6 Ferm

Wear eye and ear protection.

During use the following points must be

considered:

• Donotremoveanymechanicalorelectrical

protective provisions.

• Checkwhetheralltheprotectiveprovisions

are in place and have been attached correctly.

• Wearsafetygogglesduringdrilling.

• Ifyouhavelonghair,besuretowearhair

protection (hair net or cap). Long hair can

easily be caught in moving parts.

• Wearfittedclothing;tiebuttonsonsleeves.

• Donotholdanyworkpiecesinyourhands

when drilling. Always use a machine clamp or

another clamping tool.

• Protectworkpiecesandclampingtoolsonthe

bench to prevent them from getting caught.

Fasten them yourself with screws or clamp

them to a machine clamp fastened to the

table.

• Checkwhetherthedrillholderistightened

properly.

• Checkwhethercablelead-throughsareokay.

• Toremovedrillchipsonlyusehandbrushes,

brushes, rubber wipers, chip hooks or similar

aids.

• Donotcarryoutanycleaningorgreasingwork

while the machine is in operation.

• AlwayskeepV-beltscovered(sothatyour

hands cannot become caught).

• Onlytightenthetoothedringdrillholderby

means of the wrench.

• Neverleavethewrenchofthedrillholderin

the drill holder! Before switching on the

machine, check whether the wrench really has

been removed!

• Donotuseanydrillswhicharedamagedon

the shank.

• Drillisnotsuitabletouseaspress!

• Ifthemainscableisdamaged,itmayonlybe

replaced by a mains cable of the same type.

Immediately switch off the machine when:

• Interruptioninthemainsplug,mainsleador

mains lead damage.

• Defectswitch.

• Smokeorstenchofscorchedisolation.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

The machine is provided with a zero

voltage switch. After the tension drops

the machine will not start to run

automatically for safety reasons. The

machine must be switched on again.

Replacing cables or plugs

Immediatelythrowawayoldcablesorplugswhen

theyhavebeenreplacedbynewones.Itis

dangerous to insert the plug of a loose cable in the

wall outlet.

Using extension cables

Only use an approved extension cable suitable for

the power input of the machine. The minimum

conductor size is 1.5 mm

. When using a cable

reel always unwind the reel completely.

3. Assembly

Fig. B

• Placethefootplate(13)inthecorrectposition.

• Fastenthecolumn(11)withtheboltssupplied

(12) to the footplate.

• Nowslidethetableholder(10)withthetable

over the column (11). With the fastening

handle (6) the table is fastened into the

desired position.

• Nowyoucanassemblethemachinecasing

(7) and lock with the locking pins (8).

• Sincethedrillspindleisgreasedinthefactory,

it is advisable to run in the machine for

approximately 15 minutes at the lowest speed.

Before you push the chuck with pin (9)

into the drill spindle, the inside of the

chuck must be completely grease-free!

Setting up the bench drill

Before use the drill must be mounted on a fixed

base. The footplate (13) has therefore been

provided with drilling holes. By means of screws

the footplate can be fixed to the base in this place.

Ifitismountedonawoodenboard,sufficiently

large washers must be used on the opposite side,

so that the bolts are not pushed into the wood and

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TDM1022 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info