Bedienungsanleitung Ferm TDM1022 (Seite 8 von 40) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

632654

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

8 Ferm

the workpiece and the point of the drill. You can

also swivel the bench sideways, if you wish to

clamp a workpiece directly onto the footplate.

Fig. I

For slanted drilling and with a slanted supporting

surface of the workpiece the bench can be

swivelled. For this purpose loosen the hexagonal

screw (20) on the hinge point (21) of the bench

and remove the centring. Swivel the bench (19) to

the desired position. Then screw down the

hexagonal screw (20) properly using a wrench.

Number of revolutions, speed of rotation, supply

The supply - the feed motion of the drill - takes

place by hand on the 3-armed drill lever. The

speed of rotation is determined by the number of

revolutions of the drill spindle and by the diameter

of the drill. The correct choice of supply and the

number of revolutions of the drill spindle are the

deciding factors for the lifespan of the drill. The

following applies as a basic rule: with a larger

diameter of the drill the number of revolutions

must be adjusted lower; the greater the firmness

of the workpiece, the greater the cutting pressure

must also be.

Inordernottooverheatthedrillinthiscase,the

supply and speed of rotation must be lowered at

thesametime.Inaddition,thedrillmustbecooled

with drill oil. For thin plates, quite large drillings

must be carried out carefully with little supply and

little cutting pressure, so as to get a precise result

and so that the drilling remains the correct size.

For deep drilling (larger than 2 x the diameter of

the drill) the discharge of chips is more difficult and

the temperature of the drill is higher. Therefore

lower the supply and the number of revolutions

and ensure a better discharge of chips by regularly

pulling back the drill. For drilling with a greater

diameter than 8 mm, pre-drilling must take place,

so that early wear of the drill - main cutting edge

can be avoided and so that the drilling point is not

too heavily loaded.

5. Maintenance

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

This machine has been designed to operate over

a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine. Regularly clean

the machine housing with a soft cloth, preferably

after each use. Keep the ventilation slots free from

dustanddirt.Ifthedirtdoesnotcomeoffusea

soft cloth moistened with soapy water. Never use

solvents such as petrol, alcohol, ammonia water,

etc. These solvents may damage the plastic parts.

Please clean the tool immediately after use.

Lubrication

Every bearing in the drill press has been pre-

lubricated in the factory. Further lubrication is

unnecessary. From time to time, you should

grease the racks and pinions, the table lifting

mechanism, the spindle and the splines of the

hollow shaft. Open the drive belt guard and squirt

a little oil onto the spindle shaft. Do not allow any

oil to touch the drive belt!

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warrantycard.Inthebackofthismanualyoufind

an exploded view showing the parts that can be

ordered.

Environment

To prevent damage during transport, the appliance

is delivered in a solid packaging which consists

largely of reusable material. Therefore please

make use of options for recycling the packaging.

Damaged and/or disposed of electrical or

electronic devices must be dropped off at

recycling stations intended for that

purpose.

Warranty

Read the warranty conditions on the separately

supplied warranty card.

The product and the user manual are subject to

change. Specifications can be changed without

further notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TDM1022 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info