Bedienungsanleitung Ferm TDM1026 (Seite 6 von 88) (Alle Sprachen)

762260

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Indicates the presence of an electrical

voltage.

Immediately unplug the plug from the

mains electricity in the case that the cord

gets damaged and during maintenance.

Keep bystanders away.

Wear eye and ear protection.

During use the following points must be

considered:

• Do not remove any mechanical or electrical

protective provisions.

• Check whether all the protective provisions are

in place and have been attached correctly.

• Wear safety goggles during drilling.

• If you have long hair, be sure to wear hair

protection (hair net or cap). Long hair can

easily be caught in moving parts.

• Wear fitted clothing; tie buttons on sleeves.

• Do not hold any workpieces in your hands

when drilling. Always use a machine clamp or

another clamping tool.

• Protect workpieces and clamping tools on the

bench to prevent them from getting caught.

Fasten them yourself with screws or clamp

them to a machine clamp fastened to the table.

• Check whether the drill holder is tightened

properly.

• Check whether cable lead-throughs are okay.

• To remove drill chips only use hand brushes,

brushes, rubber wipers, chip hooks or similar aids.

• Do not carry out any cleaning or greasing work

while the machine is in operation.

• Always keep V-belts covered (so that your

hands cannot become caught).

• Only tighten the toothed ring drill holder by

means of the wrench.

• Never leave the wrench of the drill holder in the

drill holder! Before switching on the machine,

check whether the wrench really has been

removed!

• Do not use any drills which are damaged on

the shank.

• Drill is not suitable to use as press!

• If the mains cable is damaged, it may only be

replaced by a mains cable of the same type.

Immediately switch off the machine when:

• Interruption in the mains plug, mains lead or

mains lead damage.

• Defect switch.

• Smoke or stench of scorched isolation.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

The machine is provided with a zero

voltage switch. After the tension drops

the machine will not start to run

automatically for safety reasons. The

machine must be switched on again.

Replacing cables or plugs

Immediately throw away old cables or plugs

when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1.5 mm2. When using a cable

reel always unwind the reel completely.

3. ASSEMBLY

Fig. B, F

• Place the footplate (13) in the correct position.

• Fasten the column (11) with the bolts supplied

(12) to the footplate.

•

Now slide the table holder (10) with the table

over the column (11). With the fastening handle

(6) the table is fastened into the desired position.

• Now you can assemble the machine casing (7)

and lock with the locking pins (8).

• Fit the chuck guard holder onto the spindle

(21) and tighten the slotted screw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TDM1026 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info