Bedienungsanleitung Ferm TDM1026 (Seite 7 von 88) (Alle Sprachen)

762260

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

• Clean the conical hole in the chuck (9) and the

spindle with a clean piece of fabric. Make sure

there are no foreign particles sticking to the

surfaces.

• Powerfully push the chuck (9) up on the

spindle (21), as far as it wiII go.

• Fit the clear chuck guard (3) to the chuck (9)

guard holder and fasten the fixing screws.

• Since the drill spindle is greased in the factory,

it is advisable to let the machine run for

approximately 15 minutes at the lowest speed

before use.

Before you push the chuck on the drill

spindle, the inside of the chuck and the

outside of the spindle must be completely

grease-free!

Setting up the bench drill

Before use the drill must be mounted on a fixed

base. The footplate (13) has therefore been

provided with drilling holes. By means of screws

the footplate can be fixed to the base in this place.

If it is mounted on a wooden board, sufficiently

large washers must be used on the opposite side,

so that the bolts are not pushed into the wood and

the machine cannot become loose.

The fastening screws may be fastened

so far that the footplate is not under

tension or deformed. When the tension

is too high there is a risk of breakage.

Adjusting the number of revolutions of the drill

spindle

Fig. C

The different revolutions of the drill spindle can be

adjusted by shifting the V-belt into the belt drive.

The machine is protected by a safety switch so

that the machine is automaticly switched off when

opening the casing. The V-belt is shifted as follows:

• Open the V-belt cover (14) by loosen the screw

(16) on the right side of the cover.

• Loosen the fastening button (18) and slide the

motor in the direction of the machine head,

upon which the V-belt is released.

• Shift the V-belt according to the table on the

inside of the V-belt cover.

• Tension the V-belt again by pushing the motor

plate (17) to the back. Then the tensioning

device is fastened with the fastening button (18).

• Close the V-belt cover and the machine is

ready again for use.

Keep the V-belt cover closed during use.

Fig. C & D

If you have shifted the V-belt, you must tighten it

again by means of the motor plate (17) with the

fastening button (18). The tension is correct when

the V-belt can be pressed in by approximately 1

cm. The motor pulley must be aligned horizontally,

so that early wear and loosening of the V-belt can

be prevented. For this purpose the motor pulley

(15) on the motor can be slid along the motor axle,

after loosening the socket head screw.

Spindle speeds

Fig. E

Position V-belt Revolutions/min

1 500

2 890

3 1400

4 1900

5 2500

The number of revolutions of the drill spindle of

the V-belt combinations can be read from the

illustration and the table.

Test the V-belt tension before you connect the

machine to the electricity mains.

4. OPERATION, HINTS AND TIPS

Depth stop

Fig. A-1

The drill spindle is provided with a depth stop (2).

It can be adjusted using the nut. The drill depth

can be read on the scale division.

Clamping the drill

Fig. F

In the drill head of the bench drill, drills and other

tools with a cylindrical shank can be clamped.

The moment of rotation is transferred to the drill

by means of the tension of the three clamping

jaws. To prevent the drill from sliding away, it must

be clamped using the toothed ring wrench. If the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TDM1026 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info