Bedienungsanleitung Ferm TSM1029 - FZB-250-1500 (Seite 8 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Schwedisch, Norwegisch, Finnisch)

634179

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Ferm8

• Fig.Cshowstheparttobesawnout(310

x310mm),sothatthesawdustcanfall

throughitandpilingupisprevented!

 Onlyifyoudonotuseanextraction

system!

• Fastenthemachinewithbolts.

Whenusingthebase,thesamemustbexed

tothegroundusingfourboltsThesawinturn

mustbexedtothebasewithfourbolts.Check

theseboltsfortightnessbeforeswitchingonthe

machine.

Assembly and attachment of the rip fence

Fig. D1 + D2

• Attachthealuminiumfence(A)tothe

positioningblock(B).

• Nowyoucanattachthecompleteripfence

tothebenchtop.

• Slidetheripfenceviaoneendofthe

positioningrail(C)overthebenchtop.

• Adjustthepositionofthealuminiumfence

prole(A)suchthattheendcorresponds

totherearedgeofthesaw.

Assembly of the riving knife and the

protective cap

Fig. E1 - E3

• Turnthesawbladecompletelyupwards.

• Removethebenchinlay.

• Assembletherivingknifeontheset-up

forthispurposeanduseherebytheAllen

screwsandthellingrings.Ensurethatthe

rivingknifefallsproperlyintotheopening

(=groove).

• Nowputtheinlaybackinthebenchand

fastenit.

• Nowassemblytheprotectivecapontothe

rivingknifeanduseherebytheprolednut

andself-lockingnut.

Now lay a lath against the saw blade

and the riving knife and check whether

it falls properly into the extension of

the saw blade. If this is not the case:

Loosen the fastening bolts and place

or remove the lling rings.

• Abovethesawtabletheradialdistance

betweentherivingknifeandthetoothed

rimofthesawbladeshallnotatanypoint

exceed5mmatthedepthofcutset.

• Thetipoftherivingknifeshallnotbelower

than5mmfromthetoothpeak,asshown.

Assembly of the saw blade

First remove the plug from the mains

before the saw blade is assembled or

replaced.

• Removetheinlayfromthebench.Usea

screwdriverforthispurpose.

• Turnthesawaxlecompletelyupwards.

Removethenutandtheoutsideange

fromthesawaxle.

• Nowslidethesawbladeoverthesawaxle

andnowputtheoutsideangeandthenut

back.Tightenthenutbyhand.

• Nowusethe2keys:onefortheangeand

oneforthenutandnowclampit.

• Nowputtheinlaybackinthebenchand

fastenit.

Mounting the push stick holders

Fig. F2 - F4

Mountbothpushstickholdersonthesideofthe

machineusingtheboltsandringssupplied.

Use of the mitring set-up

Fig. A

Byturningthehandleatthesideofthemachine

youcanadjustthesawbladetoamaximumof

45°(4).

4. OPERATION

Working instructions

Therearetwotypesofsawingmethods:

• Lengthwisesawing

Sawing the workpiece in the length of

the wood grain.

• Cross-cuttingorcuttingoff

Sawing off the workpiece crosswise.

Ifitconcernsapanel,wedonotusually

distinguishbetweenthewoodgrain,butwe

namethemethodwherewesawoffapartof

thewidthofthepanel(lengthwisesawing)and

whenwecutoffthelength(cross-cuttingor

cutting-off).

For both sawing methods one of the

fences must be used. Therefor never

saw without a fence!

Attention!Beforeyoustartsawing,rstcheck

thefollowing:

1. Isthesawbladesecured?

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1029 - FZB-250-1500 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info