Bedienungsanleitung Ferm TSM1037 (Seite 6 von 82) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

812769

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

fully inserted into the collet or chuck. If

the mandrel is insufficiently held and/or the

overhang of the wheel is too long, the mounted

wheel may become loose and be ejected at

high velocity.

g) Do not use a damaged accessory. Before

each use inspect the accessory such as

abrasive wheels for chips and cracks,

sanding drum for cracks, tear or excess

wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped,

inspect for damage or install an undamaged

accessory. After inspecting and installing

an accessory, position yourself and

bystanders away from the plane of the

rotating accessory and run the power tool

at maximum no-load speed for one minute.

Damaged accessories will normally break apart

during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection

must be capable of stopping flying debris

generated by various operations. The dust

mask or respirator must be capable of filtrating

particles generated by your operation.

Prolonged exposure to high intensity noise

may cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken

accessory may fly away and cause injury

beyond immediate area of operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an

operation where the cutting accessory may

contact hidden wiring. Cutting accessory

contacting a “live” wire may make exposed

metal parts of the power tool “live” and could

give the operator an electric shock.

k) Always hold the tool firmly in your hand(s)

during the start-up. The reaction torque of

the motor, as it accelerates to full speed, can

cause the tool to twist.

l) Use clamps to support workpiece whenever

practical. Never hold a small workpiece in

one hand and the tool in the other hand while

in use. Clamping a small workpiece allows you

to use your hand(s) to control the tool. Round

material such as dowel rods, pipes or tubing

have a tendency to roll while being cut, and may

cause the bit to bind or jump toward you.

m) Position the cord clear of the spinning

accessory. If you lose control, the cord may

be cut or snagged and your hand or arm may

be pulled into the spinning accessory.

n) Never lay the power tool down until the

accessory has come to a complete stop.

The spinning accessory may grab the surface

and pull the power tool out of your control.

o) After changing the bits or making any

adjustments, make sure the collet nut, chuck

or any other adjustment devices are securely

tightened. Loose adjustment devices can

unexpectedly shift, causing loss of control, loose

rotating components will be violently thrown.

p) Do not run the power tool while carrying

it at your side. Accidental contact with the

spinning accessory could snag your clothing,

pulling the accessory into your body.

q) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside

the housing and excessive accumulation of

powdered metal may cause electrical hazards.

s) Do not operate the power tool near

flammable materials. Sparks could ignite

these materials.

t) Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, sanding band, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in

turn causes the uncontrolled power tool to be

forced in the direction opposite of the accessory’s

rotation. For example, if an abrasive wheel is

snagged or pinched by the workpiece, the edge

of the wheel that is entering into the pinch point

can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may

either jump toward or away from the operator,

depending on direction of the wheel’s movement

at the point of pinching. Abrasive wheels may also

break under these conditions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1037 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info