Bedienungsanleitung Ferm VCM1008 (Seite 15 von 44) (Deutsch, Englisch, Holländisch, Französisch)

818305

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Keep the machine fully upright at all

times, especially when vacuuming

liquids. If the machine is tilted or turned

over liquids may enter into the motor and

cause irreparable damage.

Switching on/off and selecting operating mode

(Fig. F)

The on/off switch (1) has three settings:

I On, vacuum cleaning only

O Off

Vacuum cleaning on and detergent spray

enabled

Carpet and furniture cleaning (Fig. G)

Vacuuming will remove larger particles,

which can’t be cleaned effectively with

the cleaning nozzles. It is highly

recommended to first vacuum the carpet

or furniture before cleaning. Use the

crevice nozzle (11) to remove particles

from furniture crevices.

Preparation:

1. Remove the dust bag (7) from the container (3).

2. Install the foam filter (6) (refer to the previous

paragraph “Filters”).

3. Mount the applicable cleaning nozzle (8/9) on

the machine (refer to the previous paragraph

“Nozzle/brush”).

4. Fill the detergent tank (16)

5. Set the on/off switch (1) to the position.

6. Press and hold the spray gun trigger (25) until

detergent starts to spray from the nozzle (8/9).

Note that it may take some time before the

detergent fills the tube (20) and reaches the

nozzle.

Cleaning:

1. Apply the nozzle (8/9) to the carpet or furniture

surface.

2. Press the trigger (25) to spray detergent while

moving the nozzle slowly and evenly across

the surface.

Dry vacuuming

Clean the HEPA filter (4) regularly to

maintain the suction power.

To avoid clogging of the HEPA filter (4) it

is recommended to use a dust collection

bag (7).

Very small particles, such as dust from

cement, soot and plaster are too fine to

be used with only the HEPA filter (4) and

risk getting into the motor and damaging

it. Therefore we strongly recommend

using a dust collection bag (7) when

cleaning these types of materials.

An overfilled, clogged dust collection bag

(7) can burst. Make sure to replace the

dust collection bag in a timely manner!

1. Install the HEPA filter (4) (refer to the previous

paragraph “Filters”).

2. Place a dust bag (7) in the container (3).

3. Mount the applicable brush or nozzle

(10/11) on the machine (refer to the previous

paragraph “Nozzle/brush”).

4. Set the on/off switch (1) to the “I” position.

Wet vacuuming

The vacuum cleaner is equipped with a

cut-off float (24). The suction power will

be cut off when the maximum filling level

is reached. When this happens, switch

the vacuum cleaner off immediately.

Remove the power plug from the mains

outlet and empty the container (3).

Clean the float (24) at regular intervals,

and inspect it for damage. A damaged

float must be replaced to ensure the safe

operation of the machine.

Never reach into the water to be

suctioned up. Danger of electric shock.

Immediately switch the machine off if

foam forms or liquids escape!

Do not use a dust collection bag (7) when

vacuuming liquids.

1. Remove the dust bag (7) from the container (3).

2. Install the foam filter (5) (refer to the previous

paragraph “Filters”).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm VCM1008 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info