Bedienungsanleitung Festool ATF 65 E (Seite 6 von 24) (Englisch)

458693

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

3 Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with a

live wire will also make exposed metal parts of the tool

live and shock the operator.

4 When ripping always use a rip fence or straight

edge guide. This improves the accuracy of cut and reduces

the chance for blade binding.

5 Always use blades with correct size and shape

(diamond vs. round) arbor holes. Blades that do not

match the mounting hardware of the saw will run eccentrically,

causing loss of control.

6 Never use damaged or incorrect blade washers or

bolts. The blade washers and bolt were specially designed

for your saw, for optimum performance and safety of

operation.

7 Causes and Operator Prevention of Kickback:

Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift up

and out of the workpiece toward the operator.

When the blade is pinched or bound tightly by the kerf closing

down, the blade stalls and the motor reaction drives the unit

rapidly back toward the operator.

If the blade becomes twisted or misaligned in the cut, the

teeth at the back edge of the blade can dig into the top surface

of the wood causing the blade to climb out of the kerf and

jump back toward operator.

Kickback is the result of tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

8 Maintain a firm grip with both hands on the saw

and position your body and arm to allow you to resist

KICKBACK forces. KICKBACK forces can be controlled by

the operator, if proper precautions are taken.

9 When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the saw

motionless in the material until the blade comes to a

complete stop. Never attempt to remove the saw from

the work or pull the saw backward while the blade is

in motion or KICKBACK may occur. Investigate and take

corrective actions to eliminate the cause of blade binding.

10 When restarting a saw in the workpiece, center

the saw blade in the kerf and check that saw teeth are

not engaged into the material. If saw blade is binding, it

may walk up or KICKBACK from the workpiece as the saw is

restarted.

11 Support large panels to minimize the risk of blade

pinching and KICKBACK. Large panels tend to sag under

their own weight. Supports must be placed under the panel

on both sides, near the line of cut and near the edge of the

panel.

12 Do not use dull or damaged blade. Unsharpened or

improperly set blades produce narrow kerf causing excessive

friction, blade binding and KICKBACK.

13 Blade depth and bevel adjusting locking levers

must be tight and secure before making cut. If blade

adjustment shifts while cutting, it may cause binding and

KICKBACK.

14 Use extra caution when making a Pocket Cut into

existing walls or other blind areas. The protruding blade

may cut objects that can cause KICKBACK.

15 Never disable the blade guard. The blade guard

provides protection from serious bodily injury - it cannot be

fully effective if tampered with.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool ATF 65 E Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info