Bedienungsanleitung Festool ATF 65 E (Seite 12 von 24) (Englisch)

458693

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

3.3 Chips extraction

Particularly for work in closed areas, we recommend that you

connect your circular saw to a chip extractor. This will enable

you to reduce the dust load in the air, ensuring that your

workplace is clean and improving the quality of your work.

For the connection of a chip extractor, the circular saw has a

suction connection piece (4.3), which can be connected to a

suction hose (4.1) with a diameter of 27 mm.

If no chip extractor is connected, it is essential that the chip

guard supplied (4.2) is fitted to the connection piece. The

chip trajectory can be altered by turning the chip guard as

required. This prevents the operator being subjected to a

stream of chips, always providing that the chip guard is

adjusted so that the chip trajectory is directed away from the

operator.

3.4 Changing the saw blade

Check regularly whether the saw blade is in good

condition. Saw blades which are cracked or have changed

shape should no longer be used, but changed immediately!

When selecting the saw blades it is essential that the following

points are observed:

- Do not use saw blades made of high alloy high speed steel

(HSS circular saws), as otherwise there is a great danger of

recoil.

- Use only saw blades that have an outside diameter of 180

to 192 mm.

- The bore diameter of the saw blade holder should be 30

mm.

- Use only saw blades with a fundamental thickness of max.

1.9 mm and a cutting width of 2.5 to 3.5 mm.

The AT 65 E was tested with Festool saw blades listed in the

Festool catalogue. For your own safety, we recommend that

you use only those saw blades.

To change the saw blade, place the circular saw on the saw

bench so that the saw blade protrudes a few millimetres

beyond the edge of the bench.

3.2 Riving kniff

The AT 65 E is fitted with a riving knife (3.2) as

standard. All saw work, with the exception of plunge cuts,

should, for safety reasons, only be carried out with the riving

knife installed and correctly set!

The riving knife must be set so that

- the distance between riving knife and cutting circle (3.3) of

the saw blade is 2 to 4 mm (measurement x), and

- the saw blade is set 2 to 4 mm above the riving knife

(measurement y).

Setting the riving knife:

- Remove the plug from the power supply socket.

- Set a cutting depth of about 50 mm, and press the saw

down to the stop. Hold the saw in this position for setting the

riving knife.

- Loosen the fixing screw (3.1) turning it about one turn to

the left with the hexagon socket wrench supplied. The safety

screw ensures that the riving knife does not drop out of the

machine during this action.

- Set the riving knife correctly, and tighten the fixing screw

up again.

Removing and installing the riving knife:

- Remove the plug from the power supply socket.

- Set a cutting depth of about 50 mm, and press the saw

down to the stop. Hold the saw in this position for the

removal.

- Loosen the fixing screw by about 2 turns to the left using

the hexagon socket wrench.

- Draw the riving knife downwards out from the protective

cover, and tighten the fixing screw again.

- To install it, reverse the process. Make sure the riving knife

is correctly set!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool ATF 65 E Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info