Bedienungsanleitung Festool ATF 65 E (Seite 14 von 24) (Englisch)

458693

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Remember that saw blades are made for sawing and the cutting

edges are correspondingly sharp. So handle the saw blade

with care.

Saw blade removal:

- Remove the plug from the power supply socket.

- Set a cutting depth of about 30 mm, and press the saw

downwards to the stop. Hold the saw in this position for the

removal.

- Press the spindle stop (5.1). Using the hexagon socket

wrench supplied (5.8), loosen the fixing screw (5.7) for the

saw blade (5.4), and unscrew it the whole way.

- Remove the spring flange (5.6).

- Pull the saw blade away from the inner flange (5.9), and

draw it downwards out from the protective cover (5.2).

Saw blade insertion:

To guarantee trouble-free running of the saw blade, the

gripping surfaces on both flanges and on the saw blade must

be totally clean before insertion.

- Remove the plug from the power supply socket.

- Set a cutting depth of 30 mm, and press the saw downwards

to the stop. Hold the saw in this position for the insertion.

- Introduce the saw blade from below into the protective cover,

and set it with the bore on the inner flange.

The direction of rotation of the circular saw and

the prescribed direction of rotation of the saw blade must be

the same! Orientation is provided by the arrows on the saw

blade (5.5) and the protective cover (5.3).

- Set the spring flange so that both its knobs engage in the

recesses of the inner flange. Take care that the saw blade

lies flush with the gripping surfaces of both flanges.

- Press the spindle stop. Using the hexagon socket wrench,

tighten the fixing screw for the saw blade. The flanges are

designed as a safety coupling. therefore the fixing screw

must be tightly fastened.

- Remove the hexagon socket wrench. Release the spindle

stop.

4 Operation

Read and understand the safety instructions

before starting work!

4.1 Setting the cutting depth

- Press the button of the cutting depth stop (6.3), and move it

along the cutting depth scale (6.1), until the cutting depth

marking (6.2) is at the required cutting depth (the scale

values apply to a saw blade diameter of 190 mm).

- Release the button of the cutting depth stop. If you now

push the unlocking block (9.1) forwards, you can press the

hand-operated circular saw down to the set cutting depth.

4.2 Setting diagonal cuts

- Before tilting, the saw table extension must be pulled

outwards to the slot (7.4)

- Loosen both the setscrews (1.5, 7.3). Tilt the saw until the

left-hand edge of the indicator (7.2) on the scale for the

diagonal setting (7.1) shows the required diagonal.

- Tighten both the setscrews again.

If the circular saw operates with a guide rail (see Chapter

6.2), the centre of gravity lies in intersecting points of the

contact surfaces of the guide rail (8.1) and the cutting edge

(8.2). With the both screws (1.14) you can re-adjust the final

position of the centre of gravity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool ATF 65 E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info