Bedienungsanleitung Festool CS70-ST65 (Seite 8 von 38) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573132

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

1 Scope of delivery (Fig. 1)

1.1 Guide unit consisting of:

2 guide rods mounted on 2 supports

1.2 1 Open-end spanner size 17

1.3 1 Open-end spanner size 10

1.4 1 Allen key 5 mm

1.5 1 Adjusting bracket, front

1.6 4 Bolts M6x16

1.7 4 Washers Ø 6

1.8 4 Bolts M8 x 25

1.9 2 Fitting angle

1.10 4 Square nuts

1.11 1 Washer 4 mm thick

(this washer is only needed as a com-

pensating washer when extension

tables and sliding table are ﬁ tted)

1.12 1 Adjusting bracket, rear

1.13 Complete table, consisting of:

aluminium proﬁ le plate with ﬁ tted

roller supports with guide rollers and

scraper

2 Technical data

Dimensions

Width: 250 mm

Length: 335 mm

Max. slide travel: 865 mm

Max. cutting length: 650 mm

3 Fitting the sliding table

The sliding table is mounted on the left of

the PRECISIO.

Proceed as follows:

• Attach one ﬁ tting angle (1.9) each onto

the front and rear of the table frame of

the PRECISIO (Fig. 2). Insert a square nut

(1.10) into the corresponding square hole

beneath the saw table for the fastening

bolt lying towards the middle of the table.

Place bottom side of ﬁ tting angle (2.3) on

the rib (2.4) on the table frame and screw

in place with bolt (2.5). The nut for the

second fastening bolt is stuck to a strip as

an assembly aid. First insert a nut from

the front into the lateral opening (2.1)

and screw in bolt. Then remove strip and

insert second nut into the rear opening

and screw rear ﬁ tting angle in place.

· Mount front and rear adjusting brackets

(5.1) on the supports (5.5) with 2 bolts

(5.4) so that the suspension lugs (5.3)

point inwards (Fig. 5). Adjusting brackets

and support must lie against one another

following assembly, do not tighten bolts

yet.

• Suspend entire guide unit (rods) by sus-

pension lugs in the notches in the ﬁ tting

angles (2.3/1.9) (Fig. 3).

• Push the head of the carriage bolt (5.2)

through the slots (2.2) in the frame, push

bolt down and tighten slightly with handle

(3.1).

• Check that the supports rest on the ad-

justing bolts (3.3) at the front and rear.

• To prepare for insertion of the sliding ta-

ble:

- Fully open clip at rotary knob (4.5).

- Locate scraper (4.6) in correct position

(bottom edge parallel to guide rod).

• Place sliding table on the inner guide rod

from the front at a steep angle (almost

vertical) (Fig. 4) so that the guide rod is

between the roller (4.4) and ball bearing

(4.3).

• Fully insert sliding table and tilt into work-

ing position (onto second guide rod).

• The sliding table can be locked with the

rotary knob (4.5).

4 Adjusting the roller guide

4.1 Checking the guide play

The play between the guide rod and guide

rollers is usually adjusted in the works. Nev-

ertheless, we recommend that the guide

play at both rollers be checked as follows:

• Push on sliding table from above. When

the sliding table is moved the outer ring

of the bottom ball bearing also rotates if

the guide play is correctly adjusted.

4.2 Adjusting the guide play

• Loosen the locking nut (4.1) with the size

17 open-end spanner.

• Adjust the position of the bearing via the

cam plate (4.2) using a size 5 Allen key

(1.4).

• Re-tighten nut (4.1) following correction

of the guide play.

5 Adjusting the table height

A correctly adjusted sliding table is approx.

1 mm higher than the top of the base ta-

ble.

5.1 Checking the table height

• Fit angle fence on sliding table.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool CS70-ST65 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info