Bedienungsanleitung Festool CS70EB-S PR (Seite 18 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573129

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

Lay the insert in position and secure with the

clamp and the rotary knob [5-1].

7.6 Setting the spacer wedge

Once the protective cover is removed, pull ﬁ rmly

on the spacer wedge [1-6] to move to one of two

catch positions. The spacer wedge is used in the

top catch position [7-2] in the all applications,

except concealed cuts.

For concealed cuts only

Remove the top protective cover.

Press down the spacer wedge ﬁ rmly to move

to the lower catch position [7-1].

When producing concealed cuts, make sure you

guide the machine accurately. Press the work-

piece ﬁ rmly onto the table. When cutting the

workpiece, make sure that the side of the work-

piece that is already cut out is not on the same

side as the fence.

After completing concealed cuts, move the

spacer wedge [1-6] back to the top position

and attach the protective cover (see chapter

6.1).

7.7 Fence

The fence can be attached at any point along

the clamping edge of the saw base and is

so versatile, it can be used as a cross stop

[Fig. 1] or a longitudinal stop [Fig. 6].

 Before attaching, make sure that the contact

surfaces of the fence are not dirty.

WARNING

Risk of injury

Always use the fence in a ﬁ xed position and

do not use to slide the workpiece along!

Fitting the fence

Open the clamping jaws using the knob [4-4].

Place the fence with guide rail [4-5] onto the

clamp rail from above.

Secure the clamp segment using the knob [4-

4].

The fence can be adjusted in the following ways:

Move the fence on the clamp segment

Unscrew the rotary knob [1-5] and move the

fence.

Move the stop ruler

Unscrew the rotary knob [4-1] and move the

fence.

 The stop ruler is stepped on one side by

8 mm. This guide rail can be used to guide

the cross stop up to the saw cut to support

the workpiece without having to remove the

top protective cover.

Adjust the angle

Unscrew the rotary knob [4-2] and lift the re-

taining pin [4-3].

The rotary retaining pin engages at the most fre-

quently used angle settings.

Adjust the position of the stop proﬁ le

Unscrew the rotary knob [4-1].

Remove the guide rail [4-6] and turn 90°.

Place the guide rail in the guide slot available.

[Fig. 4]

The dimensions of the aluminium proﬁ le provide

a high guide surface for high workpieces and a

low guide surface for ﬂ at workpieces.

Longitudinal stop

Position the stop ruler parallel to the blade to

make rip cuts.

Use the workpiece holder [6-1] for guiding

narrow workpieces.

The two rulers on the left and right of the saw

blade cutting edges [7-1] are set to zero ex works

so that the fence can be aligned with the scale

along the front edge of the table.

7.8 Fitting the splinterguard

NOTE

The splinterguard cannot be used when making

bevel cuts. Remove the splinterguard as neces-

sary.

Unscrew the rotary knob [5-1].

Slide the clamping plate forwards.

Lift the table insert [1-4] from the rear end and

remove.

Set the saw blade to the minimum cutting

depth.

Slide the splinterguard [8-3] up to the side of

the retainer [8-1].

Place the table insert [1-4] in position and

tighten the rotary knob [5-1].

Switch on the machine and move the saw blade

slowly upwards to the maximum cutting depth.

This beds in the splinterguard. The raised sec-

tion [8-4] of the splinterguard should protrude

slightly (approx. 0.3 mm) over the edge of the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool CS70EB-S PR Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info