Bedienungsanleitung Festool CTL 48 E LE EC (Seite 15 von 101) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

499174

Zoom out

Zoom in

Vorherige Seite

1/101

Nächste Seite

CTM 48 E LE EC, CTL 48 E LE EC

6 Operation

6.1 Initial operation

Open the locking clips [2-2] and remove

the top section of the machine[2-1].

Remove the accessories from the dust

container [2-3] and the packaging!

Insert a filter bag in the dust container

that fulfils statutory requirements (see

chapter 7.8).

Replace the top section [2-1] and close

the locking clips [2-2].

Attach the cable holder to the rear of the

mobile dust extractor (see Fig. [3]).

Only CTM 48 E LE EC:

Insert the sealing

plug [1-1] on the panel (see Fig. [1] ).

Connect the suction hose to the machine.

6.2 Switch on/off

Insert the plug into an earthed socket.

The switch [1-9] serves as an on/off switch.

Switch position "0"

Appliance socket [1-11] is disconnected from

the power, mobile dust extractor is switched

off.

"MAN" switch position

Appliance socket [1-11] is connected to the

power, the mobile dust extractor starts.

"Auto" switch position

Appliance socket [1-11] is connected to the

power, the mobile dust extractor starts when

the connected tool is switched on.

7 Settings

7.1 Adjusting the hose diameter

(only CTM 48 E LE EC)

Adjust the hose diameter adjuster [1-8]

to match the diameter of the connected

hose.

The monitoring devices will measure the

air speed in the extractor hose correctly

as a result (see chapter 7.9).

7.2 Connecting electric power tools

Connect the electric power tool to the ap-

pliance socket [1-11].

7.3 Connecting pneumatic tools

With the compressed air module [1-3], the

automatic switch-on function for the mobile

dust extractor also works in conjunction with

air tools.

We also recommend installing the VE service

unit (495886). The service unit filters and lu-

bricates the compressed air and enables an

adjustment of the air pressure. An IAS

adapter (454757) is available to connect Fes-

tool air tools to the IAS system.

The operating pressure of the tool must be 6

bar for the automatic switch-on unit to func-

tion correctly.

WARNING

Unauthorised voltage or frequency!

Risk of accident

The mains voltage and the frequency of

the power source must correspond with

the specifications on the machine's name

plate.

In North America, only Festool machines

with the voltage specifications 120 V/60

Hz may be used.

CAUTION

Risk of injury from tools starting up un-

expectedly

Before setting the switch to the "AUTO" or

"MAN" position, make sure that the con-

nected tool is switched off.

WARNING

Risk of injury

Observe the maximum connected loads

for the appliance socket (see chapter

"Technical data").

Make sure that the power tool is switched

off before connecting or disconnecting.

WARNING

Risk of injury

Make sure that the pneumatic tool is

switched off before connecting or discon-

necting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool CTL 48 E LE EC Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info