778638
15
Zoom out
Zoom in
Vorherige Seite
1/98
Nächste Seite
Cordless drywall screwdrivers DWC 18-2500 DWC 18-4500
Max. workable screw length 55 mm 55 mm
Weight (incl. battery pack and magazine attachment)
as per EPTA procedure 01:2014
2 kg
Weight excl. battery pack 1.2 kg
Weight excl. battery pack, incl. depth stop 1.3 kg
Weight excl. battery pack, incl. magazine attachment 1.6 kg
* Speed values based on fully charged battery
pack.
5 Parts of the machine
[1-1] Bit store
[1-2] On/off switch
[1-3] Rotational direction switch
[1-4] AUTO/MAN selector switch
[1-5] Depth stop
[1-6] Bits
[1-7] Insulated gripping surfaces (grey sha
ded area)
[1-8] Capacity display button on battery pack
[1-9] Capacity display
Accessories shown or described are not always
included in the scope of delivery.
The specified illustrations appear at the begin
ning of the Operating Instructions.
6 Commissioning
6.1 Changing the battery pack
Inserting the battery pack [2 A]
Removing the battery pack [2 B]
The battery pack is ready to use straight out of
the box and can be charged at any time.
6.2 Changing the battery pack
Inserting the battery pack [2 A]
Removing the battery pack [2 B]
The battery pack is ready to use straight out of
the box and can be charged at any time.
Further information about the battery
pack and charger can be found in the
corresponding operating manual.
7 Settings
CAUTION
Risk of injury
Only adjust the settings when the power
tool is switched off.
7.1 Changing direction of rotation [1-3]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise rota
tion
8 Tool holder, attachments
WARNING
Risk of injury, electric shock
Always disconnect the battery pack before
any type of work on the machine!
8.1 Bit holder
The bit holder enables the operator to change
drill bits quickly.
CAUTION
Risk of injury from hot and sharp tool
Do not use any blunt or faulty tools.
Wear protective gloves.
Attaching the bit holder
Move the switch [1-4] to the MAN position.
Push the bit holder [3-2] into the tool hold
er [3-4] until it clicks into place.
Place the bit [3-3] in the holder.
Then affix the depth stop to the transmis
sion housing, as described in section .
Removing the bit holder
Take out the depth stop as described in sec
tion .
Remove the bit holder from the tool holder
by pulling firmly.
8.2 Changing the bit
To change the bit [1-6], you can use the depth
stop [1-5].
English
15
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool DWC 18-4500 - 2021 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info