Bedienungsanleitung Festool DWC 18-4500 - 2021 (Seite 17 von 98) (Alle Sprachen)

778638

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

Adjusting the screw length

► Pressing on the button [8-1] slides the

depth stop [8-2] in or out, so that it can be

adjusted to the required screw length.

The screw length setting is visible on the sides

of the depth stop [8-3].

Inserting collated screws

► Firstly, draw the belt of collated

screws [9-3] through the lower magazine

guide and then thread them into the car

riage guide until a screw clicks into the

working position.

Make sure that the screws are correctly

positioned and secure by pulling gently on

the belt of collated screws.

Check that the first screw is lined up in the

screwing axis – see figure [9].

► Use the adjusting wheel [9-1] to set the re

quired insertion depth.

► Clockwise rotation will countersink the

screws further in, while anticlockwise rota

tion will countersink the screws further out.

The current setting can be read off the pre

setting display [9-2]

Once the setting is made, drive in a test screw,

then, if necessary, correct the depth setting us

ing the adjusting wheel [9-1]. Each setting ad

justment shifts the stop by ± 0.1 mm.

We recommend screwdriving in the

automatic mode – see section 9.1 b).

Removing collated screws

► Remove the collated screws by pulling up

wards once (figure [10] ) or by engaging

the transport lever at the same time as

pulling the collated screws downwards (fig

ure [10] ).

10 Working instructions

– The magazine attachment must not be held

in the area of the depth stop.

– Each screwdriving process must be com

pleted in full. Interrupting a screwdriving

process or applying pressure when screw

driving can cause the tool to malfunction.

– The collated screws must only be changed

when the tool is at a standstill.

– The magazine attachment must under no

circumstances be used in any way other

than that described in this operating man

ual.

– Use only original screwdriver bits.

– Use only original collated screws.

– The collated screws must always be kept in

their original packing.

– Always work at right angles to the board

that is being affixed.

10.1 Magazine attachment maintenance

The magazine attachment is essentially mainte

nance-free. After an extensive period of use,

however, it is recommended to clean it with

compressed air.

The magazine attachment can be lubricated

around the area of the carriage guide – see fig

ure [11b].

For the purposes of cleaning, the magazine at

tachment can be dismantled as described be

low.

Prior to cleaning, remove the collated screws

from the magazine as described in section "Re

moving collated screws".

Take the magazine attachment out of the dry

wall screwdriver.

Removing the carriage

► Push the depth stop [8-2] in to the housing

as far as it will go, until the locking but

ton [11-1] is level with the marking for car

riage removal [11-2] – see figure [11a].

► Press the locking button [11-1] and at the

same time pull the carriage out of the mag

azine – see figure [11b].

► Push the button [8-1] and at the same time

unscrew the depth stop – see figure [11c].

Removing the transport lever

► Push the button [12-1] and at the same

time slide in the direction of the arrow – see

figure [12a].

► Remove the released button [12-1] (fig

ure [12b]) together with the transport lev

er [12-2] and the spring [12-3] from the

carriage (figure [12c]).

► Clean the individual parts, replace faulty or

worn parts and then reassemble in reverse

order.

When reassembling the transport lever in

the carriage, ensure the spring [12-3] is posi

tioned correctly within the transport lever. In

correct assembly can prevent the collated

screws from being transported properly.

10.2 Acoustic warning signals

Acoustic warning signals sound and the ma

chine switches off in the following operating

states:

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool DWC 18-4500 - 2021 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info