Bedienungsanleitung Festool KS88E (Seite 18 von 138) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573124

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

blade has come to rest.

• The saw blade becomes very hot during opera-

tion; do not touch it before it has cooled down.

• Always wear protective gloves during tool

change due to the risk of injury from the sharp

tool cutters.

Removing saw blades

– Move the machine to working position.

– Push in the spindle lock (7.2) and turn 90° clock-

wise.

– Unscrew the screw (7.8) completely using the

Allen key (7.9) (left-handed thread).

– Press the on/off switch (7.3) to unlock the pivot

guard.

– Open the pivot guard (7.4) completely.

– Remove the clamping ﬂ ange (7.7) and the saw

blade.

Installing saw blades

– Clean all parts before installing them (saw blade,

ﬂ anges, screw).

– Place the saw blade on the tool spindle (7.5).

Ensure that the directions of rotation of

the saw blade (7.6) and machine (7.1)

correspond.

– Secure the saw blade with the ﬂ ange (7.7) and

the screw (7.8).

– Tighten the screw (7.8) (left-handed thread).

– Push in the spindle lock (7.2) and turn 90° anti-

clockwise.

7.4 Inserting workpiece clamps

– Insert the workpiece clamp (8.1) in one of the

two holes (8.2). The clamping ﬁ xture must face

forwards.

– Turn the workpiece clamp until the clamping

ﬁ xture is facing forwards.

7.5 Dust extraction

Harmful/toxic dusts can be produced during your

work (e.g. lead-containing paint, some types of

wood and metal). Contact with these dusts, espe-

cially inhaling them, can represent a hazard for

operating personnel or persons in the vicinity.

• Comply with the safety regulations that apply in

your country.

• Connect the electric power tool to a suitable

extraction system.

• To protect your health, wear a P2 protective

mask.

A Festool dust extractor with an extractor hose

diameter of 36 mm or 27 mm (36 mm recom-

mended due to the reduced risk of clogging) can

be connected to the extractor connector (9.1)

The ﬂ exible chip deﬂ ector (9.2) improves dust and

chip collection. Always work with a chip deﬂ ector

ﬁ tted.

The chip deflector is attached directly to the

protective cover via the bracket (10.1). The hooks

(10.2) on the bracket must slot into the recesses

(10.3) on the protective cover.

7.6 Workpiece fence

Adjusting the stop ruler

When making mitre cuts, adjust the stop rulers

(11.1) so that they do not impede the pivot guard

or come into contact with the saw blade.

– Open the clamping lever (11.2).

– Slide the stop ruler until the shortest distance

from the saw blade is max. 4.5 mm.

– Close the clamping lever again.

Removing the stop ruler

For certain mitre cuts, one of the stop rulers may

need to be removed otherwise it will collide with

the saw unit.

– Turn the screw (11.3) as far as possible into the

threaded hole (downwards).

– You can now slide out the stop ruler sideways.

– After inserting the stop ruler again, unscrew the

screw three turns.

Auxiliary stop

You can insert an auxiliary stop made from wood

(12.2) into the holes (12.1) on each stop ruler to

enlarge the fence surface. This will allow you to

position larger workpieces more securely.

Remember the following:

• The screws for securing the auxiliary stops must

not protrude above the surface.

• The auxiliary stops should be used only for 0°

cuts.

• The auxiliary stops should not affect the function

of the protective covers.

7.7 Horizontal mitre angles

You can set any horizontal mitre angle between 50°

(on the left) and 60° (on the right). Alternatively,

you can use the standard preset mitre angles.

The arrow on the pointer (13.2) indicates the cur-

rent horizontal mitre setting. The two marks on

the right and left of the pointer arrow allow you

to adjust the angle more accurately to half a de-

gree. The two marks must be congruent with the

straight lines on the scale.

Standard horizontal mitre angles

The following preset mitre angles are available:

left: 0°, 15°, 22.5°, 30°, 45°

right: 0°, 15°, 22.5°, 30°, 45°, 60°

– Move the machine to working position.

– Pull the clamp lever (13.5) upwards.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool KS88E Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info