Bedienungsanleitung Festool KS88E (Seite 20 von 138) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573124

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

securely on the workpiece. (Note: auxiliary tools

may be needed depending on the contour of the

workpiece, e.g. curved contours).

• Never machine workpieces that are to small to

clamp properly.

• Make sure that the saw blade cannot pull the

workpiece backwards into the gap between the

saw blade and the stop ruler. Users are at par-

ticular risk when performing horizontal mitre

cuts.

• Reinforce very thin workpieces (24.2) by sawing

them together with an additional strip (24.2).

Very thin workpieces can wobble or break when

being cut.

Procedure

– Place the workpiece on the saw table and push

it against the stop ruler.

– Release the lever (17.1) for the workpiece

clamp.

– Turn the workpiece clamp until the holding rod

(17.2) is over the workpiece.

– Lower the holding clamp onto the workpiece.

– Close the clamping lever (17.1).

8.2 Speed control

You can regulate the rotational speed steplessly

between 1400 and 3400 rpm using the adjusting

wheel (2.2). This enables you to optimise the cut-

ting speed to suit the respective material.

Recommended position of the adjusting wheel

Wood 3 - 6

Plastic 3 - 5

Fibreboard materials 1 - 3

Aluminium and non-ferrous proﬁ les 3 - 6

8.3 Cutting without guiding action

– Make the required adjustments to the ma-

chine.

– Secure the workpiece.

– Slide the saw unit backwards up to the fence

(towards the workpiece stop) and close the

rotary knob (1.5) for clamping the guide ﬁ xture,

or secure the saw unit in the special cutting

position (KS 120 EB only).

– Switch on the machine.

– Hold the saw unit by the handle (1.1), guide

slowly downwards and cut through the work-

piece at an even rate of advance.

– Switch off the machine and wait until the saw

blade stops completely.

– Swivel the saw unit upwards again.

8.4 Cutting with guiding action

– Make the required adjustments to the ma-

chine.

– Secure the workpiece.

– Draw the saw unit forwards along the guide

rods.

– Switch on the machine.

– Hold the saw unit by the handle (1.1) and guide

slowly downwards.

– Push the saw unit backwards at an even rate of

advance and cut the workpiece.

– Switch off the machine.

– Wait until the saw blade stops completely and

then swivel the saw unit upwards.

8.5 Bevel (KS 120 EB only)

You can use the bevel to record any angle (e.g.

between two walls) and transfer the dissecting

angle to the circular cross-cut saw. Available as

accessories.

Interior angle

– Open the clamp (18.2).

– Place the bevel with the two legs (18.1) against

the interior sides of the corner.

– Close the clamp (18.2).

– Place the bevel with one leg on a stop ruler at-

tached to the circular cross-cut saw.

– To set the dissecting angle (horizontal mitre

angle), swivel the saw unit until the laser beam

is congruent with the line (19.1) on the bevel.

Exterior angle

– Open the clamp (18.3).

– Slide the aluminium proﬁ le (18.4) on both legs

forwards.

– Place the bevel with the two legs (18.4) against

exterior sides of the corner.

– Close the clamp (18.3).

– Slide back the aluminium proﬁ le on both legs.

– Place the bevel with one leg on a stop ruler at-

tached to the circular cross-cut saw.

– To set the dissecting angle (horizontal mitre

angle), swivel the saw unit until the laser beam

is congruent with the line (19.1) on the bevel.

9 Service and maintenance

Always pull the plug out of the socket

before performing any type of work on

the machine!

All maintenance and repair work which

requires the motor housing to be opened,

must only be carried out by an authorised

service workshop.

Damaged safety devices and parts should

be repaired or replaced by an authorised

service centre unless otherwise speciﬁ ed

in the operating instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool KS88E Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info