Bedienungsanleitung Festool KS88E (Seite 21 von 138) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573124

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

Customer service and repair. Only

through manufacturer or service work-

shops: Please ﬁ nd the nearest address

at:: www.festool.com/Service

EKAT

Use only original Festool spare parts!

Order No. at: www.festool.com/Service

To ensure constant air circulation, always keep the

cooling-air openings in the motor housing clean

and free of blockages.

The machine is equipped with self-disconnecting

special carbon brushes. If they are worn, power is

interrupted automatically and the machine comes

to a standstill.

• Clean the tabletop insert [20.1] regularly and

remove wood chips, dust deposits and workpiece

offcuts from the extraction channel on the chip

deﬂ ector (see Fig. 10).

9.1 Adjusting the laser (KS 120 EB only)

If the laser beams do not line up with the cutting

edge, you can adjust both of the lasers.

Use an Allen key screwdriver (size 2.5) to do

this.

- Pierce the points (3.2 to 3.7) marked on the

sticker using the Allen key screwdriver to reveal

the adjusting screws located underneath.

• The laser beam factory settings are correct. Only

turn the adjusting screws when indicated.

- Place a test workpiece on the machine to check

the laser.

- Cut a groove in the workpiece.

- Swivel the saw head upwards and check the

setting.

Laser beam is not visible

• First check whether the laser is switched on.

If not, press the button (2.1) to switch on the

laser.

Identify which laser beam is not visible.

- Turn the adjusting screws for the left (3.3) and

right (3.5) laser until the laser beam shines on

the workpiece.

- As described, ﬁ rst (a) adjust the laser beam so

it is parallel with the scribe line, then (b) adjust

the inclination angle and ﬁ nally (c) adjust the

axial displacement of the laser beam.

a) Laser beam is not parallel with the

scribe line [Fig. 3A]

Adjust until parallel.

Left laser beam Adjusting screw (3.4)

Right laser beam Adjusting screw (3.6)

b) Laser beam strays off line when work-

piece trimmed towards the left or right

[Fig. 3B]

Adjust the inclination angle until the laser beam

no longer strays off line when workpieces are

trimmed.

Left laser beam Adjusting screw (3.3)

Right laser beam Adjusting screw (3.5)

c) Laser beam is not positioned on the cut

[Fig. 3C]

Adjust the axial displacement.

Left laser beam Adjusting screw (3.2)

Right laser beam Adjusting screw (3.7)

9.2

Correcting horizontal mitre angles

If the pointer (13.2) no longer rests on the preset

mitre angle values, you can loosen the screw (13.1)

and readjust the pointer.

If the actual (sawn) mitre cut deviates from the

preset value, you can correct this value accord-

ingly:

– Engage the saw unit in the 0° position.

– Loosen the three screws (13.3) that secure the

scale to the saw table.

– Slide the scale together with the saw unit until

the actual value is 0°. You can check this by set-

ting an angle between the stop ruler and the saw

blade.

– Tighten the three screws (13.3) again.

– Check the angle setting by making a test cut.

9.3 Correcting vertical mitre angles

If the actual value no longer corresponds with

the preset value, you can correct this value ac-

cordingly:

– Engage the saw unit in the 0° position.

– Open both screws (23.1).

– Swivel the saw unit until the actual value is 0°.

You can check this by setting an angle between

the saw table and the saw blade.

– Tighten the two screws (23.1) again.

– Check the angle setting by making a test cut.

If the pointer (22.2) no longer rests on the preset

value, you can loosen the screw (22.1) and readjust

this value.

9.4 Replacing the tabletop insert

Never work with a worn table insert (20.1), replace

it with a new one.

– To replace the table insert, unscrew the six

screws (20.2).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool KS88E Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info