Bedienungsanleitung Festool LEX 3 2 5 (Seite 17 von 101) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

499936

Zoom out

Zoom in

Vorherige Seite

1/101

Nächste Seite

LEX 3

6 Compressed-air supply and

commissioning

6.1 Compressed air preparation

The machine is designed for lubricated and

non-lubricated operation.

The Festool service unit VE must be used in

lubricated operation. Consisting of a filter,

control unit, condensation drain and lubrica-

tor, the service unit cleans and lubricates the

compressed air and keeps it free of conden-

sation. Here, the lubricator should be set so

that a drop is applied to the compressed air

approx. every 15 minutes.

Damage that occurs as a result of in-

correct compressed air processing is

excluded from warranty claims.

We recommend a service unit with a 3/8"

connector, when up to two Festool com-

pressed air tools are used.

A compressor that supplies at least 350 l/min

at an operating pressure of 6 bar should be

used to supply compressed air.

The diameter of the piping system must be

sufficiently large (at least 9 mm).

6.2 Connection for IAS hose system

[3]

The IAS hose system combines several func-

tions in one hose depending on the version:

– Compressed air supply

[3-1]

– Exhaust air extraction

[3-2]

– Dust extraction

[3-3]

6.3 Switch on/off

Switching-on: Press

[1-1]

switch.

Switching off: Release

[1-1]

switch.

7 Settings

7.1 Setting and adjusting the speed

Can be adjusted at the control lever

[1-4]

between

This enables you to optimise the material re-

moval capacity to suit the respective materi-

al or application.

7.2 Replacing the sanding pad [4]

An optimal work result can only be

achieved using original accessories and

consumables. The use of non-original

accessories or consumables invalidates the

right to claim under warranty.

Health risk:

Fitting sanding pads of in-

correct size causes excessive vibration

of the machine.

Tuned to the surface being processed, the

machine can be equipped with three sanding

pads of different hardnesses.

Hard:

Coarse and fine sanding on surfaces.

Sanding edges.

Soft:

Universal for coarse and fine sanding,

for flat and convex surfaces.

Extra-soft:

Fine sanding of moulded parts,

arches, radii. Do not use on edges.

7.3 Attaching sanding accessories

using StickFix [4b]

The suitable StickFix sandpaper and StickFix

sanding cloth can be attached quickly and

simply to the StickFix sanding pad.

Press the self-adhesive sanding accessory

onto the sanding pad

[1-5]

7.4 Dust extraction

For use of a Festool mobile dust extractor

with flow sensor

: Adjust hose diameter

of mobile dust extractor to Ø 27 mm.

To guarantee optimal dust extraction, we

recommend using Festool extractors with au-

tomatic switch-on/switch-off device for com-

pressed air machines.

CAUTION

Risk of injury

Make sure that the pneumatic tool is

switched off when you connect the com-

pressed-air supply.

CAUTION

Risk of injury

The machine should always be disconnect-

ed from the compressed air supply before

any work is carried out on the machine.

LEX 3 77/2.5 7.800 - 10.500 rpm

LEX 3 125/3, 125/5 7.500 - 9.500 rpm

LEX 3 150/3, 150/5 7.000 - 10.000 rpm

WARNING

Dust hazard

Always work with a dust extractor.

Always observe country-specific regulations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool LEX 3 2 5 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info