Bedienungsanleitung Festool MFT3 (Seite 8 von 48) (Alle Sprachen)

778799

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

1 Technical data

MFT/3

Bench dimensions (width x

length) 1157 x 773 mm

(45.6“ x 30.4“)

Bench

height

- with foldaway

legs 900 mm (35.4“)

- without foldaway

legs 180 mm (7.1“)

max. working width 700 mm (27.6“)

max. workpiece thickness 78 mm (3.1“)

Weight 28 kg (61.7 lb)

2 Symbols

Warning of general danger

Read the Operating Instructions/Notes!

The speciﬁ ed illustrations are at the beginning of

the Operating Instructions.

3 Scope of delivery

[1-1] Bench consisting of: proﬁ le frame, cor-

ner feet, perforated top, foldaway legs

[1-2] Support unit

[1-3] Guide rail FS 1080

[1-4] Swivel unit

[1-5] Pre-set proﬁ le setting rail and

[1-6] Stop ruler

[1-7] Additional clamp for stop ruler

[1-8] Stop ﬂ ag MFT/3-AR

[1-9] Deﬂ ector

4 Intended use

The multifunction table MFT/3 is designed for

safe, accurate sawing and routing in combina-

tion with Festool electric power tools.

The clamping systems included in the acces-

sories programme enable the user to attach

workpieces securely to the worktop. The base

becomes a work bench for various tasks such as

planing, sanding, carving, etc.

The user bears the responsibility for damage

and accidents caused by improper use.

5 Setting up and attaching

Accessory attachments can be secured at differ-

ent points on the multifunction table to enable

different working positions.

In the standard working position, the user stands

along one side of the bench [Fig. 2]. In these op-

erating instructions, this side of the bench is re-

ferred to as the "front".

5.1 Setting up

Screw on the knobs [2-3] until the stop is

reached. Unfold the foldaway legs and tighten

the knobs on the joints to secure. Turn the end

cap [2-1] on the right to adjust the length of the

leg and compensate for an uneven ﬂ oor surface.

The corner feet [2-4] are ﬁ tted with rubber caps

so that the bench stands securely when the legs

are folded away.

5.2 Attaching the guide rail

Stops [3-1/4-4] are attached to the longitudi-

nal proﬁ le on the front and back of the bench ex

works for the recommended working position.

The swivel unit [1-4/3-2] is secured to the longi-

tudinal back edge and the support unit [1-2/2-2]

to the longitudinal front edge.

Unscrew the height adjustment clamp [4-3] and

the rotary knob [4-1], slide the units along the

proﬁ led groove from the left up to the stop and

then tighten the rotary knob [4-1] again to se-

cure. To eliminate play, you can adjust both units

in the proﬁ led groove by turning the adjusting

screws [4-2] in the guide spring using a size 2.5

Allen key.

To make both units more accessible, lift the metal

plates all the way up and push down the clamp-

ing lever [4-3] to secure in position. If required,

you can adjust the screws [4-2] to increase the

clamping effect.

To attach the guide rail, place on the key [3-3]

and make sure that the end of the rail is resting

on the support plate and the key is located cor-

rectly in the groove.

Secure the guide rail in this position with the

two screws [3-4] and tighten using the hexagon

wrench.

5.3 Deﬂ ector

The deﬂ ector [1-9] prevents the extraction hose

and the power cable from catching on the guide

rail. The deﬂ ector is attached to the end of the

guide rail and secured with the rotary knob [1-

10].

Multifunction table

MFT/3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool MFT3 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info