Bedienungsanleitung Festool MFT3 (Seite 9 von 48) (Alle Sprachen)

778799

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

5.4

Attaching the pre-set proﬁ le setting rail

The rail can be attached at any point along the

clamping edge of the bench and is so versatile,

it can be used as a cross stop or a longitudinal

stop.

Before attaching, make sure that the V groove

on the fence is not dirty.

Open the clamping jaws using the knob [5-4].

Place the fence with guide rail [5-5] onto the

clamp rail from above.

Secure the clamp segment using the knob [5-4].

The additional clamp [1-7] is designed to secure

the stop ruler.

Guide the additional clamp into the V groove

on the MFT/3 and the guide slot on the stop

ruler.

Secure the additional clamp using the clamp

lever and the rotary knob.

6 Working with the MFT

6.1 Adjusting the pre-set proﬁ le setting rail

Check the angle setting of the pre-set proﬁ le

setting rail before starting work. Align the guide

rail ﬁ rst of all [6a].

Align the guide rail at right angles to the pre-

set proﬁ le setting rail.

If an angle of 90° is not possible, slide a sup-

port unit on the guide rail until the angle is

correct.

Secure the guide rail.

Slide the relevant stop [3-1/4-4] along the

table proﬁ le to retain the setting permanent-

ly.

If required, the pre-set proﬁ le setting rail can

also be aligned in relation to the perforated top

provided the necessary clamps (accessories) are

available.

Insert the clamps [6-1] and [6-2] as shown in

Fig. [6a] and move the stop ruler [6-3] to a 90°

position.

If the stop ruler does not rest evenly against the

clamps:

Loosen the screws [6-4] and the rotary knob

[5-2]. The retaining pin must be engaged in

the 90° notch.

Set the angle at 90° in relation to the clamps

and tighten the screws.

The fence can be adjusted in the following ways:

Adjustment parallel to the bench edge:

Loosen the rotary knob [5-4].

Slide the stop into the groove on the MFT/3.

Adjustment at right angles to the bench edge:

Loosen the rotary knob [5-4].

Slide the stop into the groove on the MFT/3.

Adjusting the stop ruler [5-6] lengthways

Loosen the rotary knob [5-1]. The stop ruler

can be moved to a lower position for thin work-

pieces or a higher position for thicker work-

pieces.

Angle adjustment using the scale

Loosen the rotary knob [5-2] and lift the re-

taining pin [5-3]. The rotary retaining pin en-

gages in the most common angle positions.

WARNING

Risk of injury

Always use the fence in a ﬁ xed position and do

not use to slide the workpiece along!

Make sure that all rotary knobs on the fence

are tightened before starting work.

Stop ﬂ ag

The adjustable stop MFT/3-AR [1-8] is used to

adjust the distance to the tool and the length of

the workpiece section being processed.

6.2 Adjusting the guide rail in relation to the

workpiece

Before sawing or routing, lower the guide rail

and support unit [1-2] until the guide rail rests

ﬂ at on the workpiece.

Caution: the nose of the support unit must be

seated in the groove on the underside of the

guide rail without play.

Clamp the swivel unit [1-4] and the support

unit [1-2] using the clamping levers.

Clamp the workpiece securely to the MFT/3

using MFT clamps (accessories) or an FSZ

clamp (accessories).

For safe machining of narrow and/or short

workpieces:

Place a piece of material of the same thick-

ness under the guide rail.

6.3 Adjusting the cutting depth for sawing

[Fig. 7]

Always make sure that the cutting depth setting

is correct in relation to the workpiece thickness.

We recommend setting a cutting depth to a max-

imum of 5 mm more than the workpiece thick-

ness to protect the proﬁ le frame from damage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool MFT3 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info