Bedienungsanleitung Festool PF1200E1 (Seite 10 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

574103

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Only guide the machine against the work-

piece when it is switched on.

When the machine is lifted, the milling unit

springs back into the starting position.

4 Machine settings

Always remove the power supply plug

from the socket before carrying out any

work on the machine.

4.1 Sensor

The sensor remains on the workpiece while it is

being routed. Its function is to determine the cut-

ting depth. Festool offers sensors for all the usual

plate thicknesses.

Changing the sensor

- Press the screws (1.1) and turn them to the

left.

- Open the ﬂ ap (1.2).

- Unscrew the four screws (1.4).

- Replace the jockey roller (1.5).

- Tighten the four screws (1.4).

- Close the ﬂ ap (1.2).

- Press the screws (1.1) and turn them to the right

until they latch into place.

4.2 Depth stop (4.5)

When the sensor is on the workpiece, i.e. in

working position, there must be a gap of 0.3 mm

between the depth stop (4.5) and the stop plate

(4.4). This limits the cutting depth, and prevents

the machine from tilting to the side while work is

in progress. This would happen if one side of the

machine moved away from the guide rail.

Use a screwdriver to adjust the three screws on

the rotating depth stop. The screws have been

set for plate thickness of 3 mm, 4 mm and 6 mm

in the factory.

4.3 Changing tools

- Press the screws (1.1) and turn them to the

left.

- Open the ﬂ ap (1.2).

- Press the spindle stop (2.1) and turn the tool

(2.4) until the spindle stop latches into place;

keep the spindle stop pressed in.

- Open the screw (2.2).

- Remove the tool (2.5) and sensor (2.4).

- Clean the contact surface between the tool

ﬂ ange, the tool, and the sensor; insert the new

tool with the sensor.

The direction of rotation on the tool must

be the same as the direction of rotation

of the machine (2.3).

- Tighten the screw (2.2) and let go of the spindle

stop

- Close the ﬂ ap (1.2).

- Press the screws (1.1) and turn them to the right

until they latch into place.

4.4 Dust extraction

Always connect the machine to a

dust extractor.

You can connect a Festool extractor with an ex-

tractor hose diameter of 36 mm to the extractor

connector (4.8).

5 Electronics

The PF 1200 E features full-wave elec-

tronics with the following properties:

Smooth start-up

The smooth start-up ensures the router starts

up jolt-free.

Speed adjustment

You can regulate the speed steplessly between

2000 and 5500 min

-1

using the adjusting wheel

(4.3). This enables you to optimise the cutting

speed to suit the material.

Constant speed

The pre-selected speed remains constant whether

the machine is in operation or in neutral posi-

tion.

Temperature control

To prevent overheating, the safety electronics

switches the machine off when it reaches a critical

motor temperature. Let the machine cool down

for approx. 3-5 minutes before using it again. The

machine requires less time to cool down if it is

running, i.e. in neutral position.

6 Working with the machine

Always secure the workpiece in such a

manner that it cannot move while being

sawed.

The machine must always be held with

both hands by the designated handles

(5.1, 5.2).

Always push the machine forwards (5.3),

never pull the machine backwards to-

wards you.

You can use the router only in connection

with the guide rail (3.1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PF1200E1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info