778610

Festool PRECISIO CS 50 EG - 2021 Seite 22

22
Zoom out
Zoom in
Vorherige Seite
1/180
Nächste Seite
22
h. Never reach around or over a rotating saw
blade. Reaching for a workpiece may lead to
accidental contact with the moving saw blade.
i. Provide auxiliary workpiece support to the
rear and/or sides of the saw table for long
and/or wide workpieces to keep them level.
A long and/or wide workpiece has a tendency
to pivot on the table’s edge, causing loss of
control, saw blade binding and kickback.
j. Feed workpiece at an even pace. Do not bend
or twist the workpiece. If jamming occurs,
turn the tool off immediately, unplug the tool
then clear the jam. Jamming the saw blade
by the workpiece can cause kickback or stall
the motor.
k. Do not remove pieces of cut-off material
while the saw is running. The material may
become trapped between the fence or inside
the saw blade guard and the saw blade pulling
your fingers into the saw blade. Turn the saw
off and wait until the saw blade stops before
removing material.
l. Use an auxiliary fence in contact with the table
top when ripping workpieces less than 2 mm
thick. A thin workpiece may wedge under the
rip fence and create a kickback.
Kickback causes and related warnings
Kickback is a sudden reaction of the workpiece
due to a pinched, jammed saw blade or misaligned
line of cut in the workpiece with respect to the
saw blade or when a part of the workpiece binds
between the saw blade and the rip fence or other
fixed object.
Most frequently during kickback, the workpiece
is lifted from the table by the rear portion of the
saw blade and is propelled towards the operator.
Kickback is the result of saw misuse and/or in-
correct operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
a. Never stand directly in line with the saw
blade. Always position your body on the same
side of the saw blade as the fence. Kickback
may propel the workpiece at high velocity
towards anyone standing in front and in line
with the saw blade.
b. Never reach over or in back of the saw blade
to pull or to support the workpiece. Accidental
contact with the saw blade may occur or kick-
back may drag your fingers into the saw blade
c. Never hold and press the workpiece that is
being cut off against the rotating saw blade.
Pressing the workpiece being cut off against
the saw blade will create a binding condition
and kickback.
d. Align the fence to be parallel with the saw
blade. A misaligned fence will pinch the
workpiece against the saw blade and create
kickback.
e. Use a featherboard to guide the workpiece
against the table and fence when making non-
through cuts such as rabbeting, dadoing or
resawing cuts. A featherboard helps to control
the workpiece in the event of a kickback.
f. Use extra caution when making a cut into
blind areas of assembled workpieces. The
protruding saw blade may cut objects that can
cause kickback.
g. Support large panels to minimise the risk
of saw blade pinching and kickback. Large
panels tend to sag under their own weight.
Support(s) must be placed under all portions
of the panel overhanging the table top.
h. Use extra caution when cutting a workpiece
that is twisted, knotted, warped or does not
have a straight edge to guide it with a mitre
gauge or along the fence. A warped, knotted,
or twisted workpiece is unstable and causes
misalignment of the kerf with the saw blade,
binding and kickback.
i. Never cut more than one workpiece, stacked
vertically or horizontally. The saw blade
could pick up one or more pieces and cause
kickback.
j. When restarting the saw with the saw blade
in the workpiece, centre the saw blade in the
kerf so that the saw teeth are not engaged in
the material. If the saw blade binds, it may lift
up the workpiece and cause kickback when the
saw is restarted.
k. Keep saw blades clean, sharp, and with suf-
ficient set. Never use warped saw blades or
saw blades with cracked or broken teeth.
Sharp and properly set saw blades minimise
binding, stalling and kickback.
Table saw operating procedure warnings
a. Turn off the table saw and disconnect the
power cord when removing the table insert,
changing the saw blade or making adjust-
… 22 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool PRECISIO CS 50 EG - 2021 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info