Bedienungsanleitung Festool PRECISIO CS 50 EG - 2021 (Seite 24 von 180) (Alle Sprachen)

778610

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

- When cutting wood, connect the machine to a

dust extractor corresponding to EN 60335-2-69,

dust class M.

- To minimise the release of dust, the machine

should be connected to a suitable dust extractor.

All dust extraction elements (dust extraction

attachments, etc.) must be properly adjusted.

- Never process material that contains asbestos.

- Make sure that you have enough light in the

room or work place.

- When sawing, adopt the correct working posi-

tion:

- At the front on the side of the operator;

- Head-on to the saw;

- Beside the line of cut.

- Use the accompanying push stick to guide the

workpiece accurately past the saw blade.

- Always use the supplied riving knife and the

guard. Ensure that they are set correctly as

described in the operating instructions. If the

riving knife is set incorrectly and components

that are required for safety reasons (such as the

guards) are removed, this may result in serious

injuries.

- Use a suitable device to support long workpieces

and ensure that they are horizontal.

- Pull the plug from the mains power socket be-

fore changing tools and rectifying faults such as

removing trapped splinters.

- Do not remove offcuts or other workpiece parts

from the cutting area while the machine is still

running or before the saw blade stops moving.

- If the saw blade is jammed, switch the machine

off immediately and disconnect the mains plug.

Do not remove the jammed workpiece until you

have done this.

- Cutting rebates or grooves is only permitted

when a suitable protective device has been ﬁtted,

e.g. a protective tunnel over the saw table.

- Reinstall the safety equipment immediately af-

ter work that requires the guard to be removed,

see section 5.2.

- Do not use circular saws for cutting slots

(grooves in workpiece).

- Before transporting the machine, make sure

that the top guard covers the top section of the

saw blade.

- Do not use the top guard as a handle for trans-

portation.

- When not in use, store the push stick in the

accessory holder provided on the machine.

- Use only original Festool accessories and aids.

- Use of your own aids e.g. push stick, rulers, etc.

is not permitted.

- Before commencing work, check that the guard

and splinter guard can move freely and are rest-

ing on the table.

- To prevent the saw blade from overheating or

the plastic from melting, set the correct speed

for the cutting material and do not use excess

pressure when cutting.

- When cutting metal, switch on the saw using a

residual current circuit breaker.

- Check the plug and the cable regularly and

should either become damaged, have them

replaced by an authorised after-sales service

workshop.

- Only for AS/NZS: The tool shall always be sup-

plied via residual current device with a rated

residual current of 30 mA or less.

4.4 Emission levels

Typically, the noise levels that are determined in

accordance with EN 62841 (see EC declaration of

conformity) are as follows:

Sound pressure level LPA = 87 dB(A)

Sound power level LWA = 101 dB(A)

Measuring uncertainty allowance K = 3 dB

Wear ear protection!

- The speciﬁed noise emission levels have been

measured in accordance with the standard test-

ing method and can be used to compare power

tools.

- The speciﬁed noise emission levels can also be

used for making preliminary estimates regard-

ing noise load.

CAUTION

The noise emissions during actual use

of the power tool can differ from the

declared values depending on the ways

in which the tool is used especially what

kind of workpiece is processed.

- Identify safety measures to protect

the operator that are based on an estima-

tion of exposure in the actual conditions

of use (taking account of all parts of the

operating cycle such as the times when

the tool is switched off and when it is run-

ning idle in addition to the trigger time).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PRECISIO CS 50 EG - 2021 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info