Bedienungsanleitung Festool ps 300 eq plus al (Seite 15 von 86) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch)

382959

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

TRION

When working with suction units, always

use a splinterguard in order to prevent the

suction channels becoming blocked.

Insert the extractor adapter into the rear

hole of the base runner in so that the hook

[2-6] catches in the notch [2-7].

Press the lever [2-5] to remove the ex-

tractor adapter.

7.6 Adjusting the base runner

The base runner can be swivelled to both

sides by up to 45° for bevel cuts.

Remove chip guard and splinterguard,

release locking screw [4-1] with Allen key

[1-4],

push base runner approx. 5 mm forwards,

set desired inclination according to the

scale [5-2],

tighten locking screw [4-1].

Für randnahes Sägen kann der Sägetisch

nach hinten versetzt werden

Remove chip guard and splinterguard,

release locking screw [4-1] with Allen key

[1-4],

push base runner to rear position so that

the centring pin [5-1] fits in the opening

[5-3],

tighten locking screw [4-1].

7.7 Adjusting the pendulum stroke

In order to process different materials with

an optimum feed movement the pendulum

jigsaws have an adjustable pendulum stroke.

Select the desired setting with the pendulum

stroke switch [1-5]:

setting 0 = pendulum stroke off

setting 3 = maximum pendulum stroke

7.8 Adjusting the number of strokes

PS 300 EQ, PSB 300 EQ

You can regulate the number of strokes step-

lessly between 1000 and 2900 min

-1 using the

adjusting wheel

[1-2; 2-3]. This enables you to

optimise the cutting speed to suit the mate-

rial.

8 Working with the machine

8.1 Free hand according to the

scribe mark

The triangular shape of the splinterguard [4-

3] shows the cutting line of the saw blade

and thus facilitates cutting to a scribe mark.

8.2 Plunge cutting without pilot

drilling

The base runner must be in the front position

for plunge cuts in timber materials (basic

setting, see Figure [1]).

Place saw on the front edge of the runner,

set saw to maximum no. of strokes and

pendulum stroke setting 3 and start the

plunge cut into the workpiece (Figure

[6]).

9 Service and maintenance

Recommended settings of the pendu-

lum stroke

Hard and soft wood,chip board,

wood fibre board

1 - 3

Wood core plywood, plywood, plas-

tics

1 - 2

Ceramic 0

Aluminium, NF metals 0 - 2

Steel 0 - 1

Recommended number of strokes

(adjusting wheel setting)

Hard and soft wood, wood core ply-

wood, plywood, chip board

Wood fibre boards 4 - 6

Plastics 3 - 6

Ceramic, aluminium, NF metals 3 - 5

Steel 2 - 4

WARNING

Risk of injury

Always secure the workpiece in such a

manner that it cannot move while being

machined.

WARNING

Risk of injury, electric shock

Always disconnect the mains plug from the

socket before performing maintenance

work on the machine!

All maintenance and repair work which re-

quires the motor housing to be opened

must only be carried out by an authorised

service workshop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool ps 300 eq plus al Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info