Bedienungsanleitung Festool PS CARVEX 420 EBQ (Seite 15 von 107) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

497992

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

C A R V E X

The specified emissions values (vibration,

noise)

– are used to compare machines.

– They are also used for making preliminary

estimates regarding vibration and noise

loads during operation.

– They represent the primary applications of

the power tool.

Increase possible for other applications, with

other insertion tools or if not maintained ade-

quately. Take note of idling and downtimes of

machine!

6Operation

Connecting and detaching the mains power

cable

[1-7]

see Fig.

[2]

Insert the plug into a socket.

The electric power tool has one button

[1-2]

on each side for switching on/off.

The

PSB 420 EBQ

also has a variable speed

trigger

[1-3]

with switch lock

[1-4]

. For con-

tinuous operation, use the button

[1-2]

7Settings

7.1 Changing tools

Selecting saw blade

Only use saw blades with a T-shank. The

saw blade should not be longer than

that required for the intended cut. To

ensure safe guidance, during the cut the saw

blade should emerge at the bottom of the

workpiece at every point.

Only use cross-set saw blades when using

the angle and adapter table. We recom-

mend Festool saw blade S 105/4 FSG.

Inserting saw blade

Always pull the mains plug out of the

socket before changing blades.

If necessary, lift up the chip guard

[3-1]

Slide the saw blade

[3-4]

into the opening

[3-2]

as far as the stop with its teeth in the

cutting direction.

Turn the saw blade

[3-4]

clockwise ap-

prox. 30°.

Check that the saw blade is secure. A

loose saw blade can fall out and cause an

injury.

If the saw blade is very small, it is advis-

able to remove the saw base (see chapter

7.4

) before inserting the saw blade.

Adjust the saw blade guide after every

saw blade change:

The saw blade guide was designed to improve

guidance of the saw blade.

Remove the saw base (see chapter

7.4

Tighten the screw

[3-6]

using the Allen

key

[3-5]

until the jaws are almost touch-

ing the saw blade.

Ejecting saw blade

When ejecting the saw blade, hold the elec-

tric power tool such that no persons or an-

imals can be injured.

Push the saw blade ejection

[3-3]

for-

wards as far as the stop.

A tool change is only possible when the tool

holder is located in the upper position!

WARNING

Unauthorised voltage or frequency!

Risk of accident

The mains voltage and the frequency of

the power source must correspond with

the specifications on the machine's name

plate.

In North America, only Festool machines

with the voltage specifications 120 V/60

Hz may be used.

WARNING

Risk of injury, electric shock

Always pull the plug out of the socket be-

fore performing any type of work on the

machine!

CAUTION

Hot and sharp tools

Risk of injury

Wear protective gloves!

NOTE

Damage to the machine or saw blade

Do not tighten the screw [3-6] too firmly!

It must be possible to move the saw blade

slightly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PS CARVEX 420 EBQ Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info