Bedienungsanleitung Festool PS CARVEX 420 EBQ (Seite 17 von 107) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

497992

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

C A R V E X

In position

, the automatic load detection is

activated: The stroke speed is reduced in

idling and is controlled to the highest value

when the blade enters the workpiece.

8 Working with the machine

When working on small or thin workpieces, al-

ways use a stable base, or the CMS module

(accessory).

When working, hold the electric power tool by

the handle and guide it along the desired cut-

ting line. For precise cuts and smooth running,

use two hands to guide the electric power tool.

Free saw guidance along a scribe mark

The triangular pointer on the splinterguard

[4-1]

indicates the cutting line of the saw

blade. This facilitates sawing along a scribe

mark.

8.1 Lighting

A continuous light or stroboscope is installed

for illuminating the cutting line:

up to approx. 2100 rpm: continuous light

from approx. 2100 rpm: stroboscope light

In overhead position (+/- 45°), the lighting

is switched off completely.

If required, you can adjust the lighting:

Plug in the electric power tool.

Press both buttons simultaneously

[1-2]

and hold for approx. 10 s until a beep

sounds.

Release both buttons

[1-2]

Press the left button (on the pendulum

stroke side) to select the stroke speed and

consequently the desired operating mode:

Press the right button to save the setting.

9 Service and maintenance

Customer service and repair

only through manufacturer or ser-

vice workshops: Please find the

nearest address at:

www.festool.com/Service

Use only original Festool spare

parts! Order No. at:

www.festool.com/Service

Damaged safety devices and components

must be repaired or replaced in a recognised

specialist workshop, unless otherwise indicat-

ed in the operating manual.

Recommended stroke speed (position

of the adjusting wheel)

Hard and soft wood, plywood board,

plywood, chip board

Hardboard 4 - A

Plastic 3 - A

Ceramic, aluminium, non-ferrous

metals

3 - 5

Steel 2 - 4

CAUTION

Material with high dust generation (e.g.

plasterboard)

Damage to machine through dust pene-

tration, risk of injury

Do not work overhead!

WARNING

The stroboscope light may make it diffi-

cult to determine the saw blade posi-

tion

Risk of injury

Ensure the work area is well illuminated.

Mode Indication

during config-

uration

Behaviour dur-

ing operation

1 Light flashes With strobo-

scope (standard)

2 Light on Permanent light

without strobo-

scope

3 Light off Light switched off

WARNING

Risk of injury, electric shock

Always disconnect the mains plug from the

socket before performing maintenance

work on the machine!

All maintenance and repair work which re-

quires the motor housing to be opened

must only be carried out by an authorised

service workshop.

EKAT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PS CARVEX 420 EBQ Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info