Bedienungsanleitung Festool PSBC400EB (Seite 18 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

573110

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

CARVEX

The charger TRC 3 can be used to charge all

Festool battery packs of the BPS and BPC se-

ries. The charger automatically detects the type

of the inserted battery (NiCd, NiMH or LiIon). A

microprocessor controls the charging process in

line with the charging state, temperature and

voltage of the battery pack.

The LED [3-1] on the charger indicates the re-

spective operating status of the charger.

LED yellow - lit continuously

Charger is ready to use.

LED green - flashing quickly

Battery pack is charged to maximum capacity.

LED green - flashing slowly

Battery pack is charged with reduced current,

LiIon is charged to 80 %.

LED green - lit continuously

Battery pack is fully charged, or charging is not

started again, because the battery is charged

to more than 80 %.

LED red - flashing

General fault display, e.g. incomplete contact,

short circuit, battery pack faulty, etc.

LED red - lit continuously

Battery temperature is outside the permitted

range.

6.4 Charger wall mount

The charger TRC 3 has two elongated holes on

its back. It can be mounted on a wall using two

screws (e.g. round head or flat head screw with

shank diameter of 5 mm) (see Fig. [3]).

7 Settings

7.1 Changing tools

Selecting saw blade

Only use saw blades with a T-shank. The

saw blade should not be longer than that

required for the intended cut. To ensure

safe guidance, during the cut the saw blade

should emerge at the bottom of the workpiece

at every point.

Only use cross-set saw blades when using

the angle and adapter table. We recommend

Festool saw blade S 105/4 FSG.

Inserting saw blade

Always disconnect the battery pack from

the machine before every tool change!

If necessary, push the chip guard [4-1] up-

wards.

Push the saw blade [4-4] into the opening as

far as the stop with its teeth in cutting direc-

tion [4-2].

Turn the saw blade [4-4] approx. 30° clock-

wise until it engages.

The guidance jaws adjust automatically to the

saw blade used.

Check that the saw blade is secure. A

loose saw blade can fall out and cause an

injury.

In the case of very short saw blades, it is ad-

visable to remove the saw table (see chap-

ter

7.4

) before inserting the saw blade.

Ejecting saw blade

When ejecting the saw blade, hold the elec-

tric power tool such that no persons or ani-

mals can be injured.

Push the saw blade ejection [4-3] forwards

as far as the stop.

If the saw blade is not ejected:

run jigsaw 3

- 10 seconds at a high speed. Actuate saw

blade ejector mechanism [4-3] once again.

7.2 Using the chip guard

The chip guard [4-1] prevents chips flying away

and improves the efficiency of the chip extrac-

tion system.

Using minimal pressure, push the chip guard

[4-1] downwards.

7.3 Inserting splinterguard

The splinterguard makes cuts with splinter-free

cutting edges possible, even on the exit side of

the saw blade.

With the machine switched off, push the

splinterguard [5-1] onto the guide up to the

saw blade [5-2],

switch on the jigsaw,

WARNING

Risk of injury, electric shock

Always disconnect the battery pack before

any type of work on the machine!

CAUTION

Hot and sharp tools

Risk of injury

Wear protective gloves!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PSBC400EB Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info