Bedienungsanleitung Festool PSC CARVEX 400 EB (Seite 19 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

497990

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

CARVEX

with the machine running (Speed range 5),

push the splinterguard in on a flat plane un-

til it is flush with the front edge of the saw

table. This beds in the splinterguard.

When it is worn, push the splinterguard ap-

prox. 3 mm further to the rear and continue

using it.

To guarantee reliable operation of the splin-

terguard, it must seal tightly on both sides

of the saw blade. For splinter-free cuts,

therefore, a new splinterguard should also

be used after every saw blade change.

7.4 Changing saw table

Open the change lever [1-8].

Removing the saw table downwards.

Assembly is performed in reverse sequence

to removal. Ensure that the saw table is

firmly seated in the guide.

Instead of the saw table, the angle table WT-

PS 400 or adaptation table ADT-PS 400 can be

installed at the support.

Never saw without the saw table, or one

of the other tables offered in the Festool

accessories program.

7.5 Dust extraction

The extraction adapter [6-3] allows jigsaws to

be connected to a dust extractor (hose diame-

ter 27 mm).

Insert the extraction adapter into the rear

opening of the saw table so that the hook

[6-2] engages in the [6-1] recess.

To remove the extraction adapter, press the

hook [6-2].

Due to the low power consumption of the

machine (low energy consumption), dust

extractors with an automatic switch-on

function will sometimes only start up

when the actual cut is made.

Set the dust extractor to continuous oper-

ation for special applications (e.g. low

stroke rate, soft wood).

7.6 Adjusting the pendulum stroke

The pendulum stroke on pendulum jigsaws can be

adjusted to machine different materials with the

correct rate of advance. Select the required set-

ting using the pendulum stroke switch [1-11]:

Position 0 = pendulum stroke off

Position 3 = maximum pendulum stroke

7.7 Stroke speed control

The number of strokes can be adjusted step-

lessly with the adjusting wheel [1-5] between

1500

and 3800 rpm (PSBC 400 EB:

1000 -

3800

rpm). This enables you to optimise the

cutting speed to suit the respective material.

In position

, the automatic load detection is

activated: The stroke speed is reduced in idling

and is controlled to the highest value when the

blade enters the workpiece.

8 Working with the machine

When working on small or thin workpieces, al-

ways use a stable base, or the CMS module (ac-

cessory).

When working, hold the electric power tool by

the handle and guide it along the desired cut-

ting line. For precise cuts and smooth running,

use two hands to guide the electric power tool.

WARNING

Dust hazard

Dust can be hazardous to health. Always

work with a dust extractor.

Always read applicable national regula-

tions before extracting hazardous dust.

Recommended pendulum stroke setting

Softwood, chip board, wood fibreboard 1 - 3

Blockboard, plywood, plastic 1 - 2

Ceramics 0

Aluminium, non-ferrous metals 0 - 2

Steel, hardwood 0 - 1

Recommended stroke speed (position

of the adjusting wheel)

Hard and soft wood, plywood board,

plywood, chip board

Hardboard 4 - A

Plastic 3 - A

Ceramic, aluminium, non-ferrous metals

3 - 5

Steel 2 - 4

CAUTION

Material with high dust generation (e.g.

plasterboard)

Damage to machine through dust pene-

tration, risk of injury

Do not work overhead!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PSC CARVEX 400 EB Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info