Bedienungsanleitung Festool PSC CARVEX 400 EB (Seite 21 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

497990

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

CARVEX

– If LiIon battery packs are to be stored for

long periods without use, they should be

charged to 40 % capacity (approx. 15 mins.

charging period).

10 Accessories

Use only original Festool accessories and Fes-

tool consumable material intended for this ma-

chine because these components are designed

specifically for the machine. Using accessories

and consumable material from other suppliers

will most likely affect the quality of your work-

ing results and limit any warranty claims. Ma-

chine wear or your own personal workload may

increase depending on the application. Protect

yourself and your machine, and preserve your

warranty claims by always using original Fes-

tool accessories and Festool consumable mate-

rial!

The order numbers of the accessories and tools

can be found in the Festool catalogue or on the

Internet under "www.festool.com".

10.1 Saw blades, other accessories

In order to saw different materials quickly and

cleanly, Festool offers saw blades for all appli-

cations that are specially designed for your Fes-

tool jigsaw.

10.2 Sawing with special base runners

The special base runners protect high-quality

surfaces against scratches and scores.

Press in the base runner at position [7-1].

At the same time, push the base runner for-

wards.

Mount another base runner and push it to

the rear until it engages.

10.3 Sawing with the angle table

The angle table WT-PS 400 is used for sawing in-

terior and exterior angles up to 45° and pipes.

Dust extraction is not possible when

sawing with the angle table!

Installing the angle table

Remove the saw table [1-10], (see chapter

7.4

Position the angle table against the saw ta-

ble support.

Close the change lever [1-8].

Ensure that the angle table is firmly seated in

the guide.

Setting the angle

Turn the adjusting wheel [8-1] to set the de-

sired angle.

You can set the values -45°, 0° and +45° using

the scale [8-2].

For 90° cuts, we recommend setting the an-

gle table to a small negative degree value to

guarantee stable running.

10.4 Sawing with the adaptation table

The adaptation table ADT-PS 400 is used for fit-

ting your jigsaw on the Festool guide rail and

the circle cutter KS-PS 400.

Installing the adaptation table

Remove the saw table [1-10], (see chapter

7.4

Mount the adaptation table [9-1] on the saw

table support.

Close the change lever [1-8].

Ensure that the adaptation table is firmly seat-

ed in the guide.

Use the extractor connector [1-7] also with

the adaptation table.

Adaptation to the guide rail FS 2

Using the Festool guide system FS 2 (Fig.

[10]) makes it easier to produce straight and

precise cuts, in particular, with material thick-

nesses up to 20 mm.

Place the jigsaw with attached adaptation

table [9-1] on the guide rail.

Adaptation to the circle cutter

The circle cutter can be used to create circular

cuts with a diameter between 120 and 3000

mm. The circle cutter can be installed from both

sides on the adaptation table.

Place the jigsaw with attached adaptation

table on the adapter [11-1] on the circle

cutter.

Insert the centring mandrel [11-2] in the

hole [11-4] on the circle cutter aligned with

the saw blade.

Clamp the measuring tape to the circle cut-

ter using the rotary knob [11-5].

Angle table position Application

Picture [8A] Angle, interior angle

Picture [8B]

Angle

Picture [8C]

Exterior angle, pipes

WARNING

Sawing cutting depths

Risk of injury

Select the saw blade length and cutting

depth so that the saw blade always stays

in the workpiece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool PSC CARVEX 400 EB Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info