Bedienungsanleitung Festool ro 125 feq-plus (Seite 11 von 62) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

389414

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

To switch off, press the switch downwards - this

releases the switch locking and it goes into the

OFF position.

See Fig. 2 for connection and disconnection of the

power cable.

Always switch the machine off before

connecting or disconnecting the mains

lead!

4 Electronics

The machine has full-wave electronics

with the following features:

Smooth start-up

The smooth start-up ensures the machine starts

up jolt-free.

Speed adjustment

You can regulate the speed steplessly between

3000 and 6000 rpm using the adjusting wheel (1.6).

This enables you to optimise the cutting speed to

suit the material.

Constant speed

The pre-selected speed remains constant whether

the machine is in operation or in neutral posi-

tion.

Temperature control

If the motor temperature becomes too high, the

power supply and speed are reduced. The tool

then only runs with reduced power to enable

rapid cooling by means of the motor ventilation.

After cooling down, the tool accelerates again

automatically.

5 Machine settings

Always remove the power supply plug

from the socket before carrying out any

work on the machine.

5.1 Sanding motion

You can use the switch (1.1) to set two different

sanding motions.

The change can only be made when the

sanding pad is stationary, as the switch

is locked in place during operation for

reasons of safety.

Rotex rotary motion (coarse sanding, polish-

ing)

The Rotex rotary motion is a combina-

tion of rotary and eccentric motions. This

position is selected for sanding with high

output (coarse sanding) and polishing.

Slide the switch (1.1) into the right position.

Eccentric motion (ﬁ ne sanding)

This position is selected for sanding with

low output for a scratch-free surface (ﬁ ne

sanding).

Press the switch (1.1) downwards and push it into

the left-hand position.

5.2 Sanding pad brake

The rubber collar (3.1) prevents the sanding pad

from revving up to maximum speed in an un-

controlled manner during eccentric motion (ﬁ ne

sanding). Because the collar wears down in the

course of time, it has to be replaced by a new one

(order no. 453 388) as soon as there is any reduc-

tion in the braking effect.

5.3 Choice and installation of the sanding

disks

Choise of sanding disk

The appliance can be ﬁ tted with three sanding

disks of different hardness depending on the

surface to be treated.

Hard: coarse sanding on surfaces, sanding at

edges.

Soft: universal for coarse and ﬁ ne sanding for ﬂ at

and curved surfaces.

Super-soft: ﬁ ne sanding on formed parts, curves,

radii. Do not use on edges!

Assembly

The FastFix system enables tool-free replacement

of the sanding pad:

- Set the switch (1.1) to the right, to the Rotex

rotary motion

- Press spindle stop (1.5), direction of movement

(3.2) ﬁ rst to the side, then forwards

- Turn the ﬁ tted sanding pad from the spindle

(right-handed thread)

- Keep the spindle stop pressed and screw on the

new sanding pad (in doing so, make sure that

the rubber collar (3.1) is correctly ﬁ tted!)

- let go of the spindle stop

Actuate the spindle stop only when the drive spin-

dle is stationary. Do not switch on the motor when

the spindle stop is pressed in.

5.4 Attaching sanding material

The appropriate Stickﬁ x sanding paper and Stick-

ﬁ x sanding felt can be fastened quickly and easily

onto the Stickﬁ x sanding base.

The self-adhesive sanding material is simply

pressed onto the sanding base (1.7) and held

safely in place by the Stickﬁ x sanding base vel-

cro surface. After use, the StickFix sandpaper is

simply pulled off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool ro 125 feq-plus Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info