Bedienungsanleitung Festool TDK 15 6 (Seite 11 von 62) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

497587

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

a danger of rupturing concealed gas/water

pipes or cutting through power cables.

- Do not open the battery pack or the charger.

Even after disconnection from the mains,

there is still a high capacitor voltage inside

the charger.

- Make sure that metal objects (such as metal

chips) do not collect in the battery pack retai-

ning slots or enter the machine through the

air vent slits (danger of short circuit).

- Protect the battery pack from excessive heat

or constant heat sources such as sunlight or

naked ﬂ ames. There is a risk of explosion.

1.3 Noise and vibration information

Cordless drill/screwdriver

The typical values determined in accordance

with EN 60745 are:

Sound pressure level 72 dB(A)

Sound-power level 83 dB(A)

Measuring uncertainty allowance K = 4 dB

The noise level can exceed 85 dB(A)

during operation.

Wear ear protection!

Vibration emission value a

(vector sum for

three directions) and uncertainty K measured

in accordance with EN 60745:

Drilling in metal a

< 2,5 m/s²

K = 1,5 m/s²

Screws a

< 2,5 m/s²

K = 1,5 m/s²

1.4 Wall mounting LC 45

The charger LC 45 has two longitudinal slots on

its rear by which it can be suspended on walls

using two screws (e.g. button-headed or ﬂ at

head screw with a shaft diameter of 5 mm).

Screw both screws into the wall 96 mm apart

until the screwhead is protruding from the wall

by approx. 4 mm.

2 Machine settings

Remove the battery pack before any adjust-

ments, maintenance or repair is carried out!

2.1 Exchanging the battery pack

Removing battery pack

Press the two buttons (1.1) and slide the bat-

tery pack forwards to remove.

Inserting battery pack

Slide the battery pack into the holder on the

underside of the handle until it latches into

place (see Fig. 1).

2.2 To change the direction of rotati-

The selector button (1.4) determines the direc-

tion of rotation. Turn button from right to left =

clockwise rotation. Turn button from left to

right = anticlockwise rotation. Selector but-

ton in central position = circuit interlock.

2.3 Shifting speeds

Change only when completely stop-

ped!

Using the shift lever (1.5), the speed can be

changed.

1. Speed: Lever forward - Figure 1 is visible.

2. Speed: Lever backwards - Figure 2 is vi-

sible.

2.4 Torque adjustment

By turning the adjustment ring (1.6) the re-

quired torque can be adjusted. The arrow (1.7)

aligns with the adjusted state.

Drilling

Drilling symbol on adjustment ring aligns with

the arrow = maximum torque.

Screws

Torque corresponding to setting:

Position 1 = low torque

Position 20 = high torque

3 Tool holding ﬁ xture, attachments

3.1 Chuck BF-FX

The chuck is used to clamp drills and bits.

a) Fitting/removing the chuck

Fitting

- Place the chuck on the drill spindle (2.5) and

twist until the hexagon key (2.4) of the chuck

latches into the hexagon socket of the drill

spindle.

- Pull the unlocking ring (2.3) forwards, press

the chuck onto the drill spindle up to the stop

and release the unlocking ring.

Removal

- Pull the unlocking ring forwards and remove

the chuck.

b) Changing tools

- Turn the clamping sleeve (2.2) anti-clockwise

to open the clamping jaws (2.1) (Note: the

spindle is automatically locked when the ma-

chine is switched off).

- Insert the tool into the chuck.

- Clamp the tool by turning the clamping sleeve

clockwise. Always make sure that the tool is

clamped centrally in the chuck.

3.2 Angle attachment DD-AS

The angle attachment permits work (drilling,

screwing) vertical to the machine’s longitudinal

axis.

a) Fitting/removing the angle attach-

ment

Fitting

- Place the angle attachment on the drill spindle

and turn until it catches in the desired position

(Note: The angle attachment can be ﬁ tted in

16 different angle settings).

- Lock the angle attachment by turning the

fastening ring (2.7) tightly clockwise.

Removal

- Turn the fastening ring anti-clockwise up to

the stop and remove the angel attachment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool TDK 15 6 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info