Bedienungsanleitung Festool TDK 15 6 (Seite 13 von 62) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

497587

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

- By keeping the battery pack in a ready for use

charger, the battery pack will be kept in a state

of readiness by ﬂ oat charging conservation.

- Do not keep discharged battery pack (maxi-

mum one month) attached to charger whene-

ver charger is detached from the power supply

(danger of deep discharging).

- A new battery pack or a battery pack not used

for a longer period of time reaches it full ca-

pacity after about 5 charging and discharging

cycles.

- Battery packs should, before charging, be fully

discharged if possible.

Continuous starting of the charging process

shortens the lifespan of the batteries.

- A considerably reduced time of operation per

charging shows that the battery pack is used

up an should be replaced by a new one.

- NiCd battery packs that are not used for lon-

ger periods should be stored in a discharged

state.

Special instructions for NiMH battery

packs:

- The output of NiMH battery packs drops no-

ticeably at ambient temperatures below 0° C

or above 45° C.

- Do not overload the tool (do not load the tool

excessively so that it comes to a standstill).

- Even if NiMH battery packs are not used, re-

charge them approx. every 4 months so that

they retain their full capacity.

- NiMH battery packs should be left for 60 min.

in the charger after every 10th fast charge

to compensate any differences in capacity

between the cells.

- Because NiMH battery packs discharge auto-

matically, store them preferably at ambient

temperatures of between 0° C and 25° C.

6.1 Changing carbon brushes

If the carbon brushes have worn to a length of

less than 6 mm, this may reduce the perfor-

mance of the machine or cause the machine

to stop. In this case, the brushes (4.2) should

be replaced.

- Unscrew the cover (4.4) and remove the worn

brushes.

- Push in the retaining plate (4.3) on the new

carbon brushes until it latches into the notches

(4.1) and screw the covers back on.

- Operate the machine in idling state for a few

minutes so that the carbon brushes attain

optimal contact.

7 Recycling battery packs

Never throw spent battery packs

into domestic waste containers!

Return spent or defective battery packs to dea-

lers, the Festool after-sales service department

or approved waste disposal facilities. This en-

sures that they are correctly recycled.

8 Warranty

Our equipment is under warranty for at least 12

months with regard to material or production

faults in accordance with national legislation.

In the EU countries, the warranty period is 24

months (an invoice or delivery note is required

as proof of purchase). Damage resulting from,

in particular, normal wear and tear, o-verloa-

ding, improper handling, or caused by the user

or other damage caused by not following the

operating instructions, or any fault acknow-

ledged at the time of purchase, is not covered

by the warranty. Damage caused by the use

of non-original accessories and consumable

material (e.g. sanding pads) is also excluded.

Complaints will only be acknowledged if the

equipment has not been dismantled before

being sent back to the suppliers or to an aut-

horised Festool customer support workshop.

Store the operating instructions, safety notes,

spare parts list and proof of purchase in a safe

place. In addition, the manufacturer‘s current

warranty conditions apply.

Note

We reserve the right to make changes to the

technical data contained in this infor-mation as

a result of ongoing research and development

work.

9 EU Declaration of Conformity

We declare under sole responsibility that this

product complies with the following norms or

normative documents:

EN 60745,EN 60335-2-29, EN 55014,

EN 61000 in accordance with the regulations

stipulated in Directive 2006/95/EC, 98/37/EC

(until 28 Dec. 2009), 2006/42/EC (from 29 Dec.

2009), 2004/108/EC.

Dr. Johannes Steimel

Head of research and development

Festool GmbH, Wendlingen, Germany

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool TDK 15 6 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info