Bedienungsanleitung Festool TPC 18-4 (Seite 18 von 111) (Alle Sprachen)

778615

Zoom out

Zoom in

Vorherige Seite

1/111

Nächste Seite

[1-9] Gear switch

[1-10] Rotational direction switch and safety

lock/transport lock

[1-11] Handle

[1-12] Thumbwheel for torque/drilling/light

ing duration on and duration off

[1-13] Belt clip

[1-14] Bit store

[1-15] Insulated gripping surfaces (grey

shaded area)

Accessories shown or described are not always

included in the scope of delivery.

The specified illustrations appear at the begin

ning of the Operating Instructions.

6 Battery pack

Before using the battery pack, check that the

battery interface is clean. Any contamination of

the battery interface may impair correct contact

and lead to the contacts being damaged.

A faulty contact may result in the machine over

heating or being damaged.

[2A] Remove the battery pack.

[2B]

klick

Insert the battery pack – until it

clicks into place.

Further information about the charger and

battery pack with capacity indicator can be

found in the corresponding operating

manual.

7 Commissioning

CAUTION

Risk of injury

► Only assemble when the power tool is

switched off!

7.1 Belt clip [1-13]

The belt clip allows the power tool to be attach

ed to work attire for brief periods. It can be at

tached to the right or left of the power tool us

ing a screw [3].

7.2 Fitting the auxiliary handle [5]

WARNING! Always use the auxiliary handle.

► Check that the auxiliary handle [5-1] is se

curely in place.

7.3 Inserting the stop bar [6]

The drilling depth can be adjusted using the

stop bar [6-1].

7.4 Switching on/off [1-5]

Press = ON, release = OFF

The speed can be continuously adjusted,

relative to the pressure applied to the

on/off switch.

Set the rotational direction switch [1-10] to the

centre position to lock the on/off switch.

The LED light [1-4] lights up when the on/off

switch [1-5] is pressed, see section 8.4.

8 Settings

CAUTION

Risk of injury

► Only adjust the settings when the power

tool is switched off.

8.1 Changing direction of rotation [1-10]

– Switch to the left = clockwise rotation

– Switch to the right = counterclockwise rota

tion

8.2 Changing gear

The gear switch [1-9] can be used to switch the

gear unit when the power tool is switched off.

8.3 Adjusting the torque [1-12]

Screwdriving

Torque corresponding to setting at the thumb

wheel [1-12]:

Position 1 = low torque

Position 13 = high torque

There is a signal when the set torque is

reached and the power tool switches off. The

power tool only starts up again if the on/off

switch [1-5] is released and pressed again.

Drilling

Marking shows the drill symbol = maxi

mum torque.

8.4 Adjust lighting [1-12]

Configure lighting at the thumbwheel [1-12].

Marking shows position 1 to 13 or drill sym

bol . The LED light [1-4] automatically

switches on and off with the power tool. The

LED light has an afterglow for a short time after

the tool has been switched off.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool TPC 18-4 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info