Bedienungsanleitung Festool TS 75 EQ (Seite 22 von 139) (Alle Sprachen)

497613

Zoom out

Zoom in

Vorherige Seite

1/139

Nächste Seite

Current limiting

Current limiting prevents excessive current

consumption under extreme overload, which

can lead to a decrease in the motor speed. The

motor immediately restarts after the load is re

moved.

Brake

The TS 75 EBQ comes with an electronic brake.

The saw blade is stopped electronically within

approximately two seconds of switching off the

machine.

6.2 Adjusting the cutting depth

The cutting depth can be set at 0–75 mm at the

cutting depth stop.

► Push down on the cutting depth stop [3-3]

and move it to the required cutting depth

(the values specified on the scale [3-1] ap

ply to 0° cuts without a guide rail),

► Release the cutting depth stop (the cutting

depth stop clicks into pace at 1 mm incre

ments).

The saw unit can now be pushed downwards as

far as the cutting depth that is set.

A threaded pin (M4x8 up to M4x12) can be

screwed into the hole [3-2] in the cutting

depth stop. By turning the threaded pin,

the cutting depth can be adjusted even

more precisely (+/- 0.1 mm).

6.3 Adjusting the cutting angle

The saw unit can be swivelled between 0° and

47°:

► Open the rotary knobs [3-4, 3-6].

► Swivel the saw unit to the desired cutting

angle [3-5].

► Retighten the rotary knobs.

The two end positions are set at the plant

to 0° and 45°. By turning the two threaded

pins [3-7] in an anti-clockwise direction,

the end position can be increased from 45°

to a maximum of 47°.

6.4 Selecting the saw blade

Festool saw blades are identified by a coloured

ring. The colour of the ring represents the ma

terial for which the saw blade is suited.

Refer to the necessary saw blade data (see sec

tion 3.1).

Colour Material Symbol

Yellow Wood

Red Laminate, mineral ma

terial

HPL/TRESPA

Green Plaster- and cement-

bonded chipboard and

fibreboard

Blue Aluminium, plastic

"$3:-

6.5 Changing the saw blade

WARNING

Risk of injury, electric shock

► Always disconnect the mains plug from the

socket before performing any work on the

machine.

CAUTION

Risk of injury from hot and sharp insertion

tool

► Do not use any blunt or faulty insertion

tools.

► Wear protective gloves when handling an

insertion tool.

Remove the saw blade

► Swivel the machine to 0° before replacing

the saw blade and adjust the maximum cut

ting depth.

► Turn the lever [4-2] as far as it will go.

► Slide the safety lock [4-1] upwards and

push the saw unit downwards until it clicks

into place.

► Loosen the screw [4-4] using the Allen

key [4-3].

► Remove the saw blade .

Inserting the saw blade

WARNING! Check the screws and flange for

contamination and only use clean and undam

aged parts.

► Insert the new saw blade.

WARNING! The direction of rotation of the

saw blade [4-9] and saw [4-7] must match.

Serious injuries may occur in the event of

non-compliance.

► Insert the outer flange [4-10] so that the pin

engages in the recess on the inner flange.

► Tighten the screw [4-4].

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool TS 75 EQ Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Festool TS 75 EQ

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info