Bedienungsanleitung First Alert DVR0805 (Seite 19 von 47) (Englisch)

795160

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Page 19

BASIC OPERATION

RECORDING

Region Cover

REGION COVER lets you block a speciﬁc portion of a channel

you do not want recorded or shown on the display screen. This

can be useful if you need to conceal a sensitive area being

captured by the camera. To use the REGION COVER:

1. From record menu click REGION COVER. The

REGION COVER menu opens.

2. Choose a channel you wish to apply the Region Cover.

3. Select ON from the SWITCH drop-down menu.

4. Click SET in REGION COVER. The screen will be replaced by the full-

screen camera view of the desired channel. Using the mouse, place

the cursor just outside the region cover square. Click and drag the

black square with your cursor to place and size the area you wish

to conceal. Up to 4 separate cover areas are available to set.

5. Right-click anywhere on the screen to return to the Region Cover menu.

6. Click OK. Click OK in the RECORD window. Click EXIT.

Step 1

You can conﬁgure motion detection for each channel (Camera)

connected to the DVR. To conﬁgure motion detection:

1. From the Main Menu click ADVANCED. Then click Motion Detect.

2. Under STATUS, select ON to enable motion detection for the

desired chan nel. Click NEXT PAGE for additional channels.

3. Under SENSITIVITY, select from the LOWEST setting

to the HIGHEST sensitive setting.

4. Under REGION, click SET. The red motion detect grid

appears over the selected channel in full screen.

5. Click the blocks in the grid to enable/disable motion detection.

Red=motion detection enabled; White=motion detection disabled.

6. Right-click anywhere on the screen to return to the Motion Detection menu.

7. The DELAY, setting will cause the recording to continue after

motion stops for the number of seconds selected.

8. SHOW MESSAGE ON will display the alarm status when

motion is detected. -See alarm status screen

9. SEND Email enables/disables sending an email alert

if desired. Email must be conﬁgured.

10. BUZZER enable the DVR to sound or not sound if motion is

detected. Click NEXT PAGE to set additional camera channels.

11. Click OK to save settings.

Step 2 - Set Recording Based on Motion

1. From the main menu click “Record”

2. Under Rec Mode click Rocord Conf.

3. Only have a check mark on “Detect” for all four periods

4. Channel should be set to desired channel or All for all channels

5. Once desired settings are set click “Ok”

6. Click “Exit” to save changes

CCTV Resolution

CCTV resolution is measured in vertical and horizontal pixel dimensions and typically

limited by the capabilities of both the camera and the recorder that you are using for your

CCTV surveillance installation. CCTV systems use an analog video signal. For television

speciﬁcations (which CCTV uses) the highest resolution that can be captured and stored

is 704 x 480 (NTSC for the United States) and 720 x 576 (PAL for Europe). This resolution is known as D1

resolution. A high end CCTV recorder is capable of recording at up to D1 resolution.

CCTV Resolutions

D1: 704 x 480

HD1 (2CIF): 704 x 240

CIF: 352 x 240

QCIF: 176 x 120

Motion Detect Menu

Alarm Status Motion Detect Grid

Region Cover

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

First Alert DVR0805 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info