Bedienungsanleitung First Alert HD6135FB (Seite 6 von 8) (Englisch)

795114

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

IF THIS HEAT ALARM SOUNDS

RESPONDING TO AN ALARM

During an alarm, you will hear a loud, repeating horn pattern:

3beeps, pause, 3 beeps, pause.

• If the unit alarms and you are not testing the unit, it is warning you

ofapotentially dangerous situation that requires your immediate

attention. NEVER ignore any alarm. Ignoring the alarm may result

in injury or death.

•Never disconnect the AC power or remove the battery back-up to

quiet an unwanted alarm. Disconnecting the power disables the

alarm so it cannot sense heat. This will remove your protection.

•If the unit alarms and you are not absolutely certain of the source

of the heat, get everyone out of the house immediately.

•

ELECTRICAL SHOCK HAZARD: Attempting to disconnect the power

connector from the unit when the power is on may result in electrical

shock, serious injury or death.

When an interconnected system of units is in alarm, the Red LED on the

unit(s) that initiated the alarm will flash in sync with the horn. The LED will not

flash on any remaining units.

WHAT TO DO IN CASE OF FIRE

•Don’t panic; stay calm. Follow your family escape plan.

•Get out of the house as quickly as possible. Don’t stop to get dressed or

collect anything.

•Feel doors with the back of your hand before opening them.

Ifadoor is cool, open it slowly. Don’t open a hot door. Keep doors

and windows closed, unless you must escape through them.

•Cover your nose and mouth with a cloth (preferably damp).

Take short, shallow breaths.

• Meet at your planned meeting place outside your home, and do a head

count to make sure everybody got out safely.

•Call the Fire Department as soon as possible from outside.

Give your address, then your name.

• Never go back inside a burning building for any reason.

• Contact your FireDepartment for ideas on making your home safer.

USING THE SILENCE FEATURES

If you are absolutely certain the alarm is caused by a non-emergency,

non-fire situation, you may use the Silence Feature to silence the Alarm.

The Silence Feature on this unit can temporarily quiet an unwanted alarm for

up to 15 minutes.

The Silence Featureis for your convenience only and will not correct a

problem.

The Silence Feature is intended to temporarily silence the Alarm horn. It will

not extinguish a fire.

Totemporarily silence the alarm:

1. Option 1: Press the Test/Silence button on the cover of the Heat Alarm

that initiated the alarm.*

Option 2: Point a universal IR remote control at the Heat Alarm that initiated

the alarm* and press the channel or volume button until the alarm is silent.

(See “Using the Remote Control Weekly Test/Silence Feature” for details).

An acknowledge tone will be issued by the Alarm to let you know that the

silence command has been received.

*To silence Heat Alarms in an interconnected series:

To silence multiple Alarms in an interconnected series, you must press the

Test/Silence button on the unit(s) that triggered the alarm. Pressing the Test/

Silence button on a unit that did not trigger the alarm will only silence that

Alarm.

NOTE: The red light under the Silence button on the initiating alarm will flash

in sync with the horn. The red light will be off on all other Heat Alarms.

If any unit will not silence and no heat is present install a new battery and

re-test it. If it still will not silence, the unit should be replaced immediately.

LOW BATTERY SILENCE FEATURE

If AC power is on, briefly press the Test/Silence button or use a Remote

Control to silence the low battery “chirp” for up to 8 hours. A brief “chirp” will

let you know that the Alarm has accepted the Low Battery Silence command.

The Alarm will continue to operate as long as AC power is supplied. However,

replace the battery as soon as possible, to maintain protection in event of a

power outage.

“LATCHING ALARM” INDICATOR

GARAGE



BEDROOM

HALL

LIVING ROOM

KITCHEN

BASEMENT

BEDROOM

LATCHING ALARM: 

Unit was exposed 

to alarm levels of Smoke

or Heat

LATCHING NOT ACTIVATED: 

Unit was not exposed 

to alarm levels of Smoke

or Heat

KEY:

The Latching Alarm Indicator is activated after an Alarm is exposed to

alarm levels of heat. After heat levels drop below alarm levels, the red LED

will begin to flash once every 5 seconds. It will continue to flash or “latch”

until you clear it using the Test/Silence button. Press and hold the

Test/Silence button until the horn sounds.

This feature helps emergency responders, investigators, or service technicians

identify which unit(s) in your home were exposed to alarm levels of heat. This

can help investigators pinpoint the initiating alarm.

RECOMMENDED LOCATIONS FOR HEAT ALARMS

In Single-Family Residences.

For minimum coverage, BRK Brands, Inc. recommends you install Heat

Alarms in any area not suitable for smoke alarms such as garages, kitchens,

utility/laundry rooms, furnace rooms and crawl spaces. Install where tempera-

tures normally remain between –10º F and 100º F (–23º C and 38º C).

For National Fire Protection Association (NFPA) information, see “Agency

Placement Recommendations for Heat Alarms and Smoke Alarms.”

RECOMMENDED PLACEMENT

Heat Alarms Recommended in New Home Construction

•The recommended location for a Heat Alarm is at the center of the ceil-

ing. At this location, the Heat Alarm is closest to all areas of the room.

•If it is not practical to install the Heat Alarm in the center of the room,

use an off-center location not less than 4 inches (102 mm) from the

sidewall.

•If it is not practical to install the Heat Alarm on the ceiling, the next

logical location is on a sidewall. A Heat Alarm mounted on a sidewall

should have the top of the unit between 4 and 12 inches (102 mm and

305 mm) from the ceiling.

•The smooth ceiling distance between Heat Alarms shall not exceed

spacings as determined by UL firetests. This Heat Alarm has a 50 foot

(15 meter) spacing.

•Reduced spacing may be required due to factors such as exposed

joists, drafts, ceiling heights greater than 10 feet (3 meters), and other

structural characteristics that may affect Heat Alarm operation. Walls,

partitions, doorways, and joists interrupt the normal flow of heat

creating new areas to be protected.

Continued...

GARAGE

BEDROOM

HALL

LIVING ROOM KITCHEN

BASEMENT

BEDROOM

INTERCONNECTED HEAT ALARMS IN

GARAGES, KITCHENS, UTILITY/LAUNDRY

ROOMS, FURNACE ROOMS AND CRAWL

SPACES AND ONLY AS A SUPPLEMENT TO

SMOKE ALARMS.

FOR MAXIMUM PROTECTION USE

INTERCONNECTED SMOKE ALARMS WITH

BATTERY BACK-UP AS SHOWN.

25 ft.

(7.8 m)

25 ft.

(7.8 m)

25 ft.

(7.8 m)

50 ft.

(15 m)

25 ft.

(7.8 m) 12.5 ft.

(3.8 m)

12.5 ft.

(3.8 m)

Heat Alarms should be mounted on the bottom

of the joists and not up in the joist channels.

First Alert HD6135FB Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info