Bedienungsanleitung Fiskars StaySharp Max - 6201 (Seite 6 von 10) (Englisch)

714368

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Fiskars Help Line: 1-877-201-3260 videos & more at: skars.com/reelmowers Fiskars Help Line: 1-877-201-3260 videos & more at: skars.com/reelmowers

Checking Cutting Performance

Preparation

1. You’ll need several 1" wide strips of standard printer paper (not

newspaper) about 8" long, a pair of work gloves and a wood block.

WARNING: The mower blades are sharp. Wear gloves when performing

this procedure, and keep ﬁngers away from the interface between the reel

and stationary blade.

2. Ensure that the mower cannot roll forward by positioning it on a ﬁrm,

level surface with a block in front of the rear wheels. Then raise the mower

to the highest cut height position to improve access.

Check #1: Do the Blades Make Contact?

1. To check if the blades make contact, face the front of the mower and

slowly pull the cutting reel (A) downward, one blade at a time, through a full

rotation or two. If you hear scraping or feel resistance, skip the remainder of

this section and proceed to Adjusting the Blades on page 11.

ATTENTION: If the cutting reel and stationary blade make contact the

mower will be difﬁcult to push and may dull the blade.

Check #2: Do the Blades Cut Properly?

1. To check if the blades cut properly, you will need to check the blades

on both the left and right side of the mower. On the left side, feed a strip

of paper up vertically from under the mower between a cutting reel blade

(A) and the stationary blade (B). About half an inch of the strip should be

visible above the stationary blade.

IMPORTANT: The StaySharp

™

Cutting System is engineered

to cut grass without contact between the blades. This cutting system

was precision set during assembly. However, since slippage may possibly

occur during shipping, handling or use, it is very important to check the

cutting performance prior to rst use and periodically thereafter. Since

slippage can occur in two directions, two checks are required to evaluate

cutting performance — both checks need to be performed on both the

left and right sides of the mower. Checking the cutting performance,

and adjusting if needed, is the most important thing you can do to

ensure that your mower always performs optimally.

A B

IMPORTANT:

Always place the

strip of paper straight

up and down, perpen-

dicular to the ground,

like a blade of grass.

Checking Cutting Performance

WARNING: Keep your ﬁngers away from the cutting region; they should

be below the stationary blade.

2. Pull the cutting reel (A) downward, observing whether the paper is cut as the

ﬁrst cutting reel blade passes.

3. Slide the paper up a half an inch at a time to check the other blades.

4. Move to the right side of the mower and check if the blades cut on that

side properly.

5. If most of the blades cut on both sides, the cutting system is set correctly.

If most of the blades do not cut, the cutting system needs to be adjusted.

Proceed to Adjusting the Blades below.

ATTENTION: Failure to correct an improperly set cutting system will result in

poor cutting performance and uncut blades of grass.

Adjusting the Blades

Adjust the blades as needed. If issues exist on both sides of the mower,

address them one side at a time.

1. The tools required are an 11 mm and 13 mm wrench.

2. Using the 13 mm wrench, loosen the two locking bolts (C) on the side you are

correcting approximately one full turn to allow for adjustment. These bolts are tight

from the assembly process to prevent any movement in shipping, and may require

some extra leverage. Use a deep-well socket or a regular socket with an

extension for best results.

3. Using the 11 mm wrench, adjust the blades using the adjustment dial (D) on

the appropriate side. Note: the nut below the dial will move during adjustment.

•

If the blades are making contact, turn the dial counter-clockwise while

rotating the cutting reel, stopping as soon as the blades lose contact.

•

If the blades didn’t cut paper, turn the dial clockwise while rotating

the cutting reel just until the blades make contact. Then turn the dial

counter-clockwise to back off slightly.

4. When properly adjusted, the cutting reel and stationary blade should be

just short of making contact. When the blades are properly adjusted,

ﬁrmly tighten the locking bolts on the side you adjusted. Conﬁrm the

cutting performance has been corrected on this side by once again

performing the two checks. If issues exist on the other side of the mower,

repeat adjustment steps.

13 mm

11 mm

Hint: If you have followed the directions for adjusting the blades and

are still not cutting paper on one or both of the sides of the mower,

tighten the locking bolts as directed in step four and take the mower

out for a test pass. If the mower cuts to your satisfaction and the

blades do not make contact, you have adjusted the mower correctly.

10 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fiskars StaySharp Max - 6201 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info