Bedienungsanleitung Fiskars StaySharp Max - 6201 (Seite 9 von 10) (Englisch)

714368

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Fiskars Help Line: 1-877-201-3260 videos & more at: skars.com/reelmowers Fiskars Help Line: 1-877-201-3260 videos & more at: skars.com/reelmowers

Care and Maintenance

IMPORTANT: To ensure long-lasting performance, protect

your mower from impact during use and storage, keep it clean

and dry and practice regular maintenance as follows.

Lubricate moving parts at least once a season and prior to winter

storage to maintain peak performance. Your mower will push easier

and last longer if all moving parts are lubricated periodically. It is also

recommended that lubrication be applied any time the mower gets wet.

General Maintenance

Keep your mower dry to prevent rust. Your mower will perform

better for longer if it is kept dry. The precision-ground blade edges of the

cutting reel and stationary blade and the bearings that carry the cutting

reel and the rear axle are most vulnerable to rust. If your mower does get

wet, dry it off with a towel and then spray it with a rust preventative as

soon as possible.

ATTENTION: Do not use solvents such as mineral spirits or kerosene to

clean your reel mower. They will damage the plastic

Keep your mower clean to eliminate potential jams and moisture that

could cause rust. Your mower will last longer and look better if it is kept

clean. After mowing, use a broom or long-bristled brush to clean any grass

clippings or other loose debris from the mower — especially around the

cutting reel and the bottom of the drive system cover. Removing grass

clippings prevents cutting and drive system jams and eliminates trapped

moisture that could cause rust.

ATTENTION: Do not use a garden hose to wash your mower. Storing the

mower wet will allow rust to form.

Care and Maintenance

Inspect your blades at least once a season and anytime your mower

strikes a hard object. While your mower features the Fiskars

exclusive

StaySharp

™

Cutting System with hardened steel blades, blade damage

may still occur if rocks, concrete edges or other hard debris are struck.

Before checking for blade damage, ensure that the mower cannot roll

forward by positioning it on a ﬁrm, level surface with blocked rear wheels.

Examine the entire length of the ground edges on all ﬁve cutting reel

blades and the stationary blade. If a dent or ding is found, determine if

the ding causes the cutting reel and stationary blade to touch. To do this,

slowly pull the cutting reel downward while listening for scraping and

feeling for resistance in the area of the ding. If there is no contact, there is

no need to repair the ding. Simply treat it with rust preventative and

re-inspect periodically in case raised edges appear with continued use.

WARNING: The mower blades are sharp. Wear gloves when

performing this procedure, and keep ﬁngers away from the interface

between the reel and stationary blade.

To avoid further damage, repair any ding that causes the cutting reel

and stationary blade to touch as quickly as possible. With care, any

ding found can be repaired with little or no impact on your mower’s cutting

performance. Before beginning, get a narrow ﬁne ﬁle (like the one found in

the Fiskars’

Tool Care Kit, Model 7862) and position the mower on a ﬁrm,

level surface with blocked rear wheels to ensure that it cannot roll forward.

To remove the ding, ﬁle away only enough of the raised material to allow

the cutting reel to spin without making contact with the stationary blade.

File with long, straight strokes perpendicular

to the cutting edge of the blade, trying to

avoid removing material from the cutting

edge itself. When the raised edges are ﬁled

down, check the cutting gap as described in

Checking Cutting Performance on page 10.

WARNING: The mower blades are sharp. Wear gloves when

performing this procedure, and keep ﬁngers away from the interface

between reel and stationary blade.

ATTENTION: Do not use a power tool to repair blades. Too much steel

will be removed, resulting in severe blade damage and greatly reduced

cutting performance.

To Maintain Peak Cutting Performance. Your mower features a non-

contact StaySharp

™

Cutting System that cuts grass without the reel and

bedknife blades actually touching. Under normal usage conditions,

StaySharp

™

blades should stay sharp for the life of the mower. In the

unlikely event that the blades on a heavily used mower begin to show

signs of wear, Fiskars recommends backlapping to restore the blade

edges. Instructions and supplies are available in Fiskars’ StaySharp

™

Blade Restoration Kit, Model 362150-1001.

ATTENTION: Fiskars does not recommend sharpening the StaySharp

™

Max mower. The equipment and processes used in home sharpening

kits, and even by many professional sharpeners, will likely not be able to

achieve the strict tolerances required to maintain the non-contact nature of

the StaySharp

™

cutting system.

Drive Chain (A): Spray lubricant through the drive system lubrication hole

while slowly rolling the mower forward to move the chain.

Rear Wheel Bearings (B): Spray lubricant between each wheel and

side plate.

Cutting Reel Bearings (C): Spray lubricant on both ends of the cutting reel

shaft, which is located under the grass discharge chute (D).

Front Fork Assembly (E): Spray lubricant on both ends.

Cut Height Adjustment Lever (F): Spray lubricant on the cut height

adjustment lever through the slot in the cover (G).

Hint: It is recommended that a silicone-based lubricant be used.

A lubricant that leaves a dry ﬁlm instead of an oily or tacky surface

is recommended in order to keep dirt, dust and grass clippings

from sticking to the reel blades.

Fiskars StaySharp Max - 6201 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info