1
. Insert lower handles into the deck and push down
(B1).
2
. Using a pozi drive screwdriver insert the screws into
the deck and handles and fully tighten
(B2)
.
IMPORTANT INFORMATION
When received from the Manufacturer, the wheels are in a raised position. Do not switch on
the product before removing from the raised position into position 5. (See fig A)
Assembly of Lower Handles to Lawnmower
Assembly of Upper Handles to Lower Handles
1. Ensure the upper handle is located correctly with the
lock-off button on the switchbox uppermost.
2. Insert the nut into the handle knob.
(C1)
3. Ensure the upper handle and the lower handle are
aligned correctly
(C2)
. There are two holes for upper
handle height adjustment.
3. Fit the bolt, washer and handle knob
(C2).
Tighten
the handle knob.
4. Repeat on the other side.
5. Fit the cable to the handles with the clips provided.
See Contents page for position. Make sure the cable
is not trapped between the upper and lower handles.
Attaching the Cable Hooks (for storage of the mains
cable)
1. Insert the post on the Cable Hook through the hole in
the Upper Handle
(D1)
.
2. Insert the smaller screw and tighten to secure
(D2)
3. Repeat on the other side.
mower close to swimming pools or garden ponds.
8. Do not walk backwards when operating, you could trip.
9. Never cut grass by pulling the product towards you.
10. Switch off before pushing the product over surfaces
other than grass.
11. Never operate the product with damaged guards or
without guards in place.
12. Keep hands and feet away from the cutting means at
all times and especially when switching on the motor.
13. Do not tilt product when the motor is running
.
1
4. Do not put hands near the grass discharge chute.
1
5. Never pick up or carry a product when it is operating
or still connected to the mains supply.
16. Remove the plug from the mains :
- before leaving the product unattended for any period;
- before clearing a blockage;
-
before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your product until you
are sure that the entire product is in a safe operating
condition.;
- if the product starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Caution: Do not touch rotating blade(s)
2. Keep all nuts, bolts and screws tight to be sure the
product is in safe working condition.
3. Check the grassbox frequently for wear or deterioration.
4. Replace worn or damaged parts for safety.
5. Only use the replacement parts specified for this
p
roduct.
6
. Be careful during adjustment of the product to
prevent entrapment of the fingers between moving
blades and fixed parts of the machine.
7. Store in a cool dry place and out of reach of children.
Do not store outdoors.
8
. Allow the product to cool for atleast 30 minutes
before storing.
Safety
Grassbox Assembly
Grassbox Assembly
1. Locate the grassbox lid onto the grassbox by aligning
the clips. Ensure all clips are correctly located before
clicking into position
(E)
Fitting Fully Assembled Grassbox to Lawnmower.
1. Lift safety flap
(F1)
2. Make sure the discharge chute is clean and free from
debris
(F2)
3. Locate fully assembled grassbox onto 2 location
points
(F3)
at the rear of the deck as illustrated in
pic.
G
4. Locate safety flap onto the top of the grassbox.
Ensure the grassbox is securely located.
•
IMPORTANT ! AFTER FITTING ENSURE NO GAP
REMAINS BETWEEN THE SAFETY FLAP AND THE
GRASSBOX.
• Removal is the reverse procedure.
• For larger areas of grass where grass collection is not
required you can use your lawnmower without the
grassbox. Ensure the Safety Flap is fully closed. The
design of the safety flap permits the cut grass to be
discharged downward behind the machine.
Cutting Height Adjustment
• Height of cut is adjusted by raising or lowering the
wheels using the height adjustment lever
(H)
• There are five heights of cut on this product (20-60 mm).
Heights of cut:-
1 & 2 - low, 3 - medium, 4 & 5 - high
•
NOTE
A medium height of cut is recommended for most
lawns. The quality of your lawn will suffer and
collection will be poor if you cut too low.
Starting and Stopping
To Start your Lawnmower
1. Attach the extension cable to the back of the
switchbox.
(J)
2. Form a loop in the cable and push the loop through
the slot.
(K)
3. To secure, position the loop over the hook and pull the
cable back through the slot
(L)
.
4. Connect the plug to the mains and switch on.
The switchbox is provided with a lock-off button (M1) to
prevent accidental starting.
5. Press and hold the lock-off button
(M1)
on the
switchbox, then squeeze one of the Start/Stop levers
towards the upper handle
(N)
.
6. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button
(P)
.
•
NOTE - There are two start/stop levers fitted. Either
one can be used for starting the lawnmower.
To Stop your Lawnmower
1. Release the pressure on the Start/Stop lever.
ENGLISH - 2
5765592-02 Flymo Chevron 34VC-37VC Euro.qxp_???????-01 Visimo-Easimo Euro(Cleva) 08/01/2016 11:41 Page 9
