Bedienungsanleitung Frico IHW (Seite 7 von 12) (Englisch)

787190

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Installation and operating instructions

General Instructions

Read these instructions carefully prior to

installation and use. Keep this manual for

future reference.

The product may only be used as set out in

the assembly and operating instructions. The

guarantee is only valid should the product

be used in the manner intended and in

accordance with the instructions.

Application

The infrared heater IH is powerful with a

high ﬁlament temperature of 2200 °C and

is the perfect choice for exposed outdoor

environments where design is important. IH

is available in two different designs. IHW gives

a comfortable heat in the occupied zone from

close range and also wider heat distribution.

IHF has more direct heat distribution and is

designed to be installed higher up.

Protection class: IP44.

Positioning

The heaters must be placed so that they

cover the area to be heated, see ﬁg. 1. The

normal mounting height is 2–3 metres above

the ground/ﬂoor. A rule of thumb for infrared

heaters is that 600–800 W/m² increases the

experienced temperature by about 10 °C. The

output demand can be reduced if the area to

be heated is protected. If the area only has a

roof, at least 800 W/m² should be installed.

600 W/m² is sufﬁcient if the area has three

walls. For enclosed areas, the output demand

must be calculated. Optimum comfort is

achieved if the heat is distributed from at

least two directions.

IHW provides wide heat distribution (60°),

recommended installation height 1.8 – 2.5 m.

IHF provides directed heat distribution (40°),

recommended installation height 2.3 – 3.5 m.

Start-up

When the unit is used for the ﬁrst time or

after a long period of non-use, smoke or an

odour may result from dust or dirt which has

collected on the element. This is completely

normal and disappears after a short time.

Mounting

IH is installed horizontally on walls with

supplied bracket. The heater can be angled

up to 45°. The heater can also be mounted

on e.g. a parasol or a post, a suitable U-bolt

(not included) is used for this together with

the supplied console. For ceiling installation

use ceiling bracket IHE (accessory). For other

mounting alternatives, see accessories.

For minimum distance, see diagrams on

introductory pages.

1. Secure the bracket on the wall with at least

2 screws. If the keyhole slots are used, an

addition screw is needed to ﬁx the bracket.

See the introduction pages.

2. Remove the screws ﬁxed to the unit's back

on delivery.

3. Hook the unit on the bracket.

4. Lock in position with the screws.

Connection

IH is equipped with a 0.9 metre cord with

plug for connection to an earthed outlet

socket.

The connection cord must not rest against

the unit as the surface becomes hot or can

be hit by thermal radiation. Contact an

electrician if the cord needs to be changed.

Note that due to the high temperatures in the

heater, a cord of the type H05 RN-F 3G1 mm²

or the like should be used.

As the halogen lamp has a high starting

current the wall socket should be fuse

protected by a slow burn fuse.

In the event of uncertainty contact an

electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Frico IHW Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Frico IHW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info