Bedienungsanleitung Frico IHW (Seite 8 von 12) (Englisch)

787190

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Maintenance

The power supply to the unit must be

disconnected during all service, repair and

maintenance work.

The unit has no moving parts so the

maintenance requirement is small, but it

must be kept clean and free from dust and

dirt. If the reﬂector is not clean the thermal

radiation from the unit will decrease and the

heater will become hotter. A large amount of

dirt can cause overheating.

The surface of the reﬂector is sensitive and

must be cleaned with care. If the reﬂector

is dirty it must be cleaned or replaced by a

specialist.

Replacing the lamp

The heat lamp is of the highest quality and

unless it is subjected to mechanical strains in

the form of vibrations and impact it will last

for a long time. The service life is dependent

on the ambient temperature and how the

heater is installed. When the heater is

installed freely and outdoors the temperature

will be low and the life of the lamp can be

expected to be in the region of 3000 hours.

The lamp must be replaced by an installer

or other skilled person.

1. Disconnect the power supply.

2. Wait until the unit is cold.

3. Remove the covers at both ends (four

screws).

4. Pull the grille to one side.

5. Remove both reﬂector ends (two screws).

6. Loosen the connections on the terminal

block.

7. Pull the lamp out of the lamp holders.

8. Check that the replacement lamp has the

correct output and voltage.

9. Fit the new lamp. Note do not touch the

lamp with your ﬁngers, wear gloves or the

like.

10. The protective tube must be reﬁtted to the

cables, so that the cables are not damaged

when the grille is ﬁtted.

11. Reassemble the unit again.

See the introduction pages.

Residual current circuit breaker

When the installation is protected by means

of a residual current circuit breaker, which

trips when the appliance is connected,

this may be due to moisture in the heating

element. When an appliance containing a

heater element has not been used for a long

period or stored in a damp environment,

moisture can enter the element.

This should not be seen as a fault, but is

simply rectiﬁed by connecting the appliance

to the main supply via a socket without a

safety cut-out so that the moisture can be

eliminated from the element. The drying

time can vary from a few hours to a few days.

As a preventive measure, the unit should

occasionally be run for a short time when it is

not being used for extended periods of time.

Packaging

Packaging materials are chosen with

consideration to the environment and are

therefore recyclable.

Handling of product at end of working life

This product may contain substances

necessary for the functionality of the

product but potentially dangerous for the

environment. The product should not be

disposed of mixed with general household

waste but delivered to a designated collection

point for environmental recycling. Please

contact the local authority for further details

of your nearest designated collection point.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Frico IHW Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Frico IHW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info