Bedienungsanleitung Friedland GlobalGuard Home Alarm System (Seite 18 von 232) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

560834

Zoom out

Zoom in

Vorherige Seite

1/232

Nächste Seite

6.2.2.3 External siren (EXT. SIREN) – Wireless siren (WIREFREE SIREN)

You can enable and disable the external siren.

6.2.2.4 External siren (EXT. SIREN) – Night alarm (NIGHT ALARM)

You can prevent the control panel from initiating a full-alarm condition between 22:00 pm to 6:00 am to avoid the alarm sound

disturbing the neighbourhood. If the function is disabled, no alarm will sound between 22:00 pm to 6:00 am.

6.2.2.5 Error beep (ERROR BEEP)

If an abnormal condition has occurred, the event log indicator will flash and the control panel will emit an error beep.

If the event log indicator flashes while the system is disarmed and the control panel beeps periodically, this indicates an alarm

has occurred. Access the event log to make the event log indicator stop flashing and the control panel stop beeping.

Note: The control panel will not emit an error beep between 10:00 pm and 6:00 am.

6.2.2.6 Radio-frequency jamming detection (RF JAMMING DETECTION)

The radio-frequency jamming detection will continuously scan for radio-frequency jamming signals on the system operating

frequency.

6.2.2.7 Alarm relay (ALARM RELAY)

You can set the time for which the external hard-wired relay contacts will operate after an alarm has been triggered.

6.2.2.8 Zone lockout (ZONE LOCKOUT)

You can prevent a single zone from triggering an alarm more than three times before the system is disarmed.

6.2.2.9 Part arm-I setup (PART ARM-I SETUP)

You can set how long the exit delay expires when the system is armed as “Part Arm-I” mode.

6.2.2.10 Part arm-II setup (PART ARM-II SETUP)

You can set how long the exit delay expires when the system is armed as “Part Arm-II” mode.

6.2.2.11 Fully arm setup (FULLY ARM SETUP)

You can set how long the exit delay expires when the system is armed as “Fully Arm” mode.

6.2.2.12 Holiday arm setup (HOLIDAY ARM SETUP)

You can set how long the exit delay expires when the system is armed as “Holiday Arm” mode.

6.2.2.13 Date (DATE)

You can set the current date.

6.2.2.14 Time (TIME)

You can set the current time.

6.2.2.15 Remote keypad (WIREFREE KEYPAD)

The control panel can learn up to 6 remote keypads.

1. Learning the remote keypad (LEARNING ID)

a) Enter the 4-digit ID code and press the button on the remote keypad. The control panel emits two short beeps.

The display shows “NEW DEVICE”.

Note: If the remote control has already been linked, the control panel will emit one long beep.

b) Enter the 4-digit ID code and press the button on the remote keypad within 15 seconds to confirm the ID code.

The control panel emits three short beeps. The display shows “DEVICE CONFIRMED” > “SAVING NEW DEVICE”.

Note: If the confirmation signal is not received within 15 seconds, the control panel will emit one long beep and exit learn

mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Friedland GlobalGuard Home Alarm System Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Friedland GlobalGuard Home Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info