Bedienungsanleitung Friedland GlobalGuard Home Alarm System (Seite 19 von 232) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

560834

Zoom out

Zoom in

Vorherige Seite

1/232

Nächste Seite

Message

Meaning

LEARNING OK

The ID code was learned by the control panel successfully.

TIME OUT

If you do not press the buttons on the remote keypad within 60 seconds,

a time-out will occur.

ID DUPLICATE

The same ID code was learned by the control panel beforehand.

2. Enabling and disabling the remote keypad (KEYPAD WORK)

You can enable and disable a remote keypad.

3. Deleting the remote control (DEL KEYPAD)

You can delete the settings of the remote keypad from the control panel.

6.2.2.16 Linking the control panel to the Spectra lighting receiver (LINK PANEL TO SPECTRA) (optional)

When the Spectra receiver is in test mode, press the button to link the control panel to the Spectra lighting receiver.

6.2.2.17 Lighting setup for Spectra lighting receiver (LIGHTING SETUP) (optional)

You can set the operation mode (OPERATION MODE) and the lamp-on time (LAMP-ON TIME) for the Spectra lighting receiver.

If the control panel is linked to a Spectra lighting receiver and the Spectra lighting control is enabled, any alarm condition

(except fire alarms) will switch the linked lighting on for the set light-on duration.

Note: You can only set the start time and stop time from the GlobalGuard PC setup software.

If the Spectra lighting is configured as 24-hour, the lights will be triggered at any time an alarm occurs. If the Spectra lighting is

configured as time-controlled, the lights will only be triggered if the alarm occurs before the programmed stop time or after the

programmed start time. If the alarm occurs between the stop time and the start time, the lights will not be triggered.

6.2.2.18 Language setup

You can set the display language for the control panel.

Note: The control panel may only display the English language. The German language is subject to be added in the near future.

6.2.3 Security detector zone setup (SECURITY DETECTOR ZONE)

PROGRAM MODE

3. SECURITY DETECTOR

ZONE

Wireless detector

zones:

3-1 WIRELESS

DETECTOR ZONE

INPUT (01-32)

DETECTOR ZONE

:1 LEARNING ID

SEND CODE. WAITING 30S...

Wired detector zones:

3-2 WIRED DETECTOR

ZONE

INPUT (33-36)

DETECTOR ZONE

:1 WIRED ZONE

:2 LOCATION

NONE / FRONT DOOR / BACK DOOR / PATIO

DOOR / DINING ROOM / LIVING ROOM / LOUNGE

/ STUDY / PLAY ROOM / KITCHEN / UTILITY ROOM

/ HALL / LANDING / BEDROOM 1 / BEDROOM 2 /

BEDROOM 3 / BEDROOM 4 / BEDROOM 5 / SHED

/ GARAGE / PIR / MAG / SMOKE 1 / SMOKE 2 /

SMOKE 3

:3 MODEL TYPE

PIR DETECTOR / DOOR CONTACT / FIRE/SMOKE /

FLOOD DETECTOR / GAS DETECTOR / CO

DETECTOR / EMERGENCY UNIT

:4 SECURITY TYPE

INTRUDER / 24 HR INTRUDER / FIRE / TEST /

PANIC/PA

:5 CHIME MODE

SELECT ON>* / OFF>#

:6 PART-ARM-I

SELECT ON>* / OFF>#

:7 PART-ARM-II

SELECT ON>* / OFF>#

:8 DETECTOR STATUS

SELECT ON>* / OFF>#

:9 DETECTOR REMOVE

SELECT YES>*/ NO>#

:10 SIREN AT TRIGGER

SELECT ON>* / OFF>#

:11 ENTRY DELAY

SELECT ON>* / OFF>#

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Friedland GlobalGuard Home Alarm System Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Friedland GlobalGuard Home Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info