Bedienungsanleitung Frigidaire FPGH3077RF (Seite 30 von 36) (Englisch)

590299

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

CARE AND CLEANING

Cleaning the cooktop and surface burners

To avoid possible burns turn off all of the surface burners

and allow them to cool.

Any additions, changes or conversions required in order for

this appliance to satisfactorily meet the application needs

must be made by an authorized qualified agency.

Routinely clean the cooktop. Wipe with a clean, damp cloth

and wipe dry to avoid scratches. Keeping the surface

burner head ports and slots clean will prevent improper

ignition and an uneven flame.

To clean recessed and contoured areas of cooktop

If a spill occurs on or in the recessed or contoured areas,

blot up spill with an absorbent cloth. Rinse with a clean,

damp cloth and wipe dry.

To clean burner grates

• Clean when the grates are cool. Use nonabrasive

plastic scrubbing pad and mild abrasive cleanser.

• Food soils containing acids may affect the finish. Clean

immediately after the grates are cool. Thoroughly dry

grates immediately following cleaning.

To clean burner caps

• Remove caps from burner heads after they have

cooled. Clean heavy soils with a plastic scrubbing pad

and absorbent cloth. Thoroughly dry burner caps imme-

diately following cleaning including the bottom and

inside of cap.

• Do not use abrasive cleaners. Do not clean burner caps

in the dishwasher. Do not operate surface burners

without burner caps properly in place.

To clean the surface burner heads

For proper gas flow it may be necessary to clean the burner

head and slots. First use a clean damp cloth to soak up any

spills. Remove any food from between the burner slots

using a small nonabrasive brush like a toothbrush and wipe

up using a damp cloth. For stubborn soils located in the

slots, use a small-gauge wire or needle to clean. The

electrode must be carefully cleaned. Take care not to hit the

electrode with any thing hard or it could be damaged.

To clean the burner head ignition ports

Each burner head has a small ignition port (Figure 38).

Should you experience ignition problems it may be that this

port hole is partially blocked with soil. With the burner head

in place, use a small wire gauge needle or the end of a

paper clip to clear the ignition port.

Replacing the oven light

The interior oven lights are located at the rear of the oven

cavity and are covered with glass shields. The glass shield

must be in place whenever the oven is in use (Figure 39).

1. Turn electrical power off at the main source or unplug

the appliance.

2. Remove interior oven light shield by turning the shield

gently counter-clockwise and pull the shield straight out.

Do not twist or turn.

3. Replace bulb with a new appliance bulb. Replace glass

oven light shield.

4. Turn power back on again at the main source (or plug

the appliance back in). Be sure to reset the time of day

on the clock.

Figure 38: Gas burner head parts

Be sure the oven is unplugged and all parts are cool

before replacing oven light.

Figure 39: Oven light protected by glass shield

slots

ignition port

orice port

CAUTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Frigidaire FPGH3077RF Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info