Bedienungsanleitung Fujitsu LifeBook T4220 Tablet PC (Seite 73 von 136) (Englisch)

510508

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Troubleshooting

Your Tablet PC appears to

change setup parameters

when you start it.

BIOS setup changes were not

saved when you made them

and exited the BIOS setup

utility returning it to

previous settings.

Make sure you select Save Changes And Exit when

exiting the BIOS setup utility.

The BIOS CMOS back-up

battery has failed.

Contact your support representative for repairs.

This is not a user-serviceable part.

Video Problems

The built-in display is blank

when you turn on your

Tablet PC.

The angle of the display and

the brightness settings are not

adequate for your lighting

conditions.

Move the display and the brightness control until

you have adequate visibility.

The optional Port Replicator is

attached, an external monitor

is plugged in, and the Tablet

PC is set for an external

monitor only.

Pressing [F10] while holding down the [Fn] key

allows you to change your selection of where to

send your display video. Each time you press the

combination of keys you will step to the next

choice. The choices, in order are: built-in display

only, external monitor only, both built-in display

and external monitor.

The power management

timeouts may be set for very

short intervals and you failed

to notice the display come on

and go off again.

Press any button the keyboard, or move the mouse

to restore operation. If that fails, push the Suspend/

Resume button. (The display may be shut off by

Standby mode, Auto Suspend or Video Timeout)

The Tablet PC turned on

with a series of beeps and

your built-in display is

blank.

Power On Self Test (POST)

has detected a failure which

does not allow the display

to operate.

Contact your support representative.

Your system display won’t

turn on when the system is

turned on or when the

system has resumed.

The system may be password-

protected.

Check the status indicator panel to verify that the

Security icon is blinking. If it is blinking, enter your

password.

The display goes blank by

itself after you have been

using it.

The Tablet PC has gone into

Video Timeout, Standby

Mode, or Hibernate Mode

because you have not used it

for a period of time.

Press a button on the keyboard, or move the mouse

to restore operation. If that fails, push the Suspend/

Resume button. Check your power management

settings, or close your applications and go to the

Power Savings menu of the setup utility to adjust the

timeout values to better suit your operation needs.

See “BIOS Setup Utility” on page 39.

The power management time-

outs may be set for very short

intervals and you failed to

notice the display come on

and go off again.

Press any button on the keyboard, or move the mouse

to restore operation. If that fails, push the Suspend/

Resume button. (The display may be shut off by

Standby Mode, Auto Suspend or Video Timeout)

The display does not close. A foreign object, such as a

paper clip, is stuck between the

display and the keyboard.

Remove all foreign objects from the keyboard.

Problem Possible Cause Possible Solutions

T Series.book Page 63 Wednesday, April 25, 2007 11:29 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fujitsu LifeBook T4220 Tablet PC Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info