Bedienungsanleitung Fujitsu LifeBook T4220 Tablet PC (Seite 75 von 136) (Englisch)

510508

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Troubleshooting

POWER ON SELF TEST MESSAGES

The following is an alphabetic list of error-and-status

messages that Phoenix BIOS and/or your operating

system can generate and an explanation of each message.

Error messages are marked with an *. If an error

message is displayed that is not in this list, write it down

and check your operating system documentation both

on screen and in the manual. If you can find no

reference to the message and its meaning is not clear,

contact your support representative for assistance.

nnnn Cache SRAM Passed

Where nnnn is the amount of system cache in kilobytes

successfully tested by the Power On Self Test. (This can

only appear if you have an SRAM PC Card installed.)

*Extended RAM Failed at offset: nnnn

Extended memory not working or not configured prop-

erly. If you have an installed memory upgrade module,

verify that the module is properly installed. If it is prop-

erly installed, you may want to check your Windows

Setup to be sure it is not using unavailable memory

until you can contact your support representative.

nnnn Extended RAM Passed

Where nnnn is the amount of memory in kilobytes

successfully tested.

*Failing Bits: nnnn The hex number nnnn

This is a map of the bits at the memory address (in

System, Extended, or Shadow memory) which failed the

memory test. Each 1 (one) in the map indicates a failed

bit. This is a serious fault that may cause you to lose data

if you continue. Contact your support representative.

*Fixed Disk x Failure or Fixed Disk Controller

Failure (where x = 1-4)

The fixed disk is not working or not configured prop-

erly. This may mean that the hard drive type identified

in your setup utility does not agree with the type

detected by the Power On Self Test. Run the setup utility

to check for the hard drive type settings and correct

them if necessary. If the settings are OK and the message

appears when you restart the system, there may be a

serious fault which might cause you to lose data if you

continue. Contact your support representative.

*Invalid NVRAM media type

Problem with NVRAM access. In the unlikely case that

you see this message you may have some display prob-

lems. You can continue operating but should contact

your support representative for more information.

*Keyboard controller error

The keyboard controller test failed. You may have to

replace your keyboard or keyboard controller but may

be able to use an external keyboard until then. Contact

your support representative.

*Keyboard error

Keyboard not working. You may have to replace your

keyboard or keyboard controller but may be able to

use an external keyboard until then. Contact your

support representative.

*Keyboard error nn

BIOS discovered a stuck key and displays the scan code

for the stuck key. You may have to replace your keyboard

but may be able to use an external keyboard until then.

Contact your support representative.

*Operating system not found

Operating system cannot be located on either drive A: or

drive C: Enter the setup utility and see if both the fixed

disk, and drive A: are properly identified and that the

boot sequence is set correctly. Unless you have changed

your installation greatly, the operating system should be

on drive C:. If the setup utility is correctly set, your hard

drive may be corrupted and your system may have to be

re-installed from your back up media.

*Parity Check 1 nnnn

Parity error found in the system bus. BIOS attempts to

locate the address and display it on the screen. If it

cannot locate the address, it displays “????”. This is a

potentially data destroying failure. Contact your

support representative.

*Parity Check 2 nnnn

Parity error found in the I/O bus. BIOS attempts to

locate the address and display it on the screen. If it

cannot locate the address, it displays “????”. This is a

potentially data destroying failure. Contact your

support representative.

*Press <F1> to resume, <F2> to SETUP

Displayed after any recoverable error message. Press

the [F1] key to continue the boot process or the [F2]

key to enter Setup and change any settings.

*Previous boot incomplete –

Default configuration used

Previous Power On Self Test did not complete success-

fully. The Power On Self Test will load default values and

offer to run Setup. If the previous failure was caused by

incorrect values and they are not corrected, the next

boot will likely fail also. If using the default settings does

not allow you to complete a successful boot sequence,

you should turn off the power and contact your support

representative.

T Series.book Page 65 Wednesday, April 25, 2007 11:29 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fujitsu LifeBook T4220 Tablet PC Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info